Automated Fiber Optical inspection Systems
See Also: Inspection Systems, X-ray Inspection Systems
-
Product
Fiber Optic Temperature Sensor with the EasyDisk
The TPT-62
-
The TPT-62 fiber-optic temperature probe family employs industry standard 62.5µm core OM1 fiber optic for highly improved optical, mechanical, and reliability properties over legacy 200 µm core (1st generation) fiber optic sensors. The EasyDisk sensor tip assembly ensures IEC60076-2 (Annex E) compliant installation and enables quick insertion of the probes into the spacers within the windings of transformers.
-
Product
Printed Circuit Board Inspection System
-
NIDEC-READ offers an array of testing equipment used to conduct open/leak tests on motherboards, as well as many other printed circuit boards. They can be flexibly configured according to applications in terms of size, type, and the number of test pins required.
-
Product
Automated Engine Testing System
-
Automated engine test system is intended for comprehensive testing of electrical motors with shaft rotation frequency up to 70 000 rpm. Such engines include:*high-voltage motors;*traction engines;*internal combustion engines;*AC motors;*DC motors;*synchronous engines;*asynchronous engines;*asynchronous engines with short-circuit rotor.
-
Product
Packaged Food X-ray Inspection System
EPX100
-
Our revolutionary new x-ray system is so advanced it will not only improve your product safety and meet regulatory compliance but also will optimize and streamline your product inspection.
-
Product
Automated Excise Stamp Control System
Kama
-
The automated control (verification) system of excise stamps allows for blotting accounting of alcohol, dairy and other products (inspection of the readability of DataMatrix, PDF, QR, Barcode and other barcodes of excise or federal stamps) at a speed of up to 20 pcs / s. This visual inspection allows you to quickly identify defects in DM and PDF printing. The recognition system also analyzes gaps and doubles in a sequence of codes. The system has its own mechanism for rewinding a roll with a volume of up to 5000 marks. All types of stamps (old and new, large and small) are supported. Wide range of options for configuring scanning parameters and automatic generation of reports for the EGAIS department. Possibility of manual scanning (by hand scanner).
-
Product
Test Automation Platform Developer's System
KS8400A
-
The Keysight KS8400A Test Automation Platform (TAP) Developer's System provides powerful, flexible and extensible test sequence and test plan creation with additional capabilities that optimize your test software development and overall performance. Keysight TAP is a modern Microsoft .NET-based application that can be used stand-alone or in combination with higher-level test executive software environments. Leveraging C# and the power of Microsoft Visual Studio, TAP is not just another programming language. It's a platform upon which you can build your test solutions, maximizing your team's productivity by using your existing software development tools and infrastructure.
-
Product
Smart Factory Inspection System
-
API, recognizing manufacturing industry’s increasing demand for part measurement automation, with a higher degree of accuracy, has developed its Smart Factory Inspection System with true 6 Degrees of Freedom (6DoF) real-time 3D robotic measurement incorporating its proven metrology technology and calibration components.SFIS can be delivered as a customized integrated solution or as a standard production inspection cell.
-
Product
PXIe System Sync Module, 2 Port
M9032A
System Sync Module
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
Product
GPR System for Concrete Inspection
StructureScan™ Mini
-
Geophysical Survey Systems, Inc.
The StructureScan Mini safely locates metallic and non-metallic targets within concrete structures up to a depth of 20 inches. The system incorporates an auto target feature that marks the detection of features of interest. This function also estimates the depth of targets and automatically adjusts the depth scale.
-
Product
3D X-ray hybrid inspection system
YSi-X
-
Ideal for 100% inspection of onboard automotive products and many other items by 3D X-rays acquire layered of target. X-ray, optical, infrared, and laser height measurement as standard equipment; hybrid and high reliability with multiple inspection modes.
-
Product
High-Definition Distributed Fiber Optic Sensing
ODiSI
-
Luna’s ODiSI system provides the world’s highest resolution distributed fiber optic sensing solution for strain and temperature measurement. Using low-profile optical fiber as sensors, the ODiSI system maps strain and temperature fields with sub-millimeter spatial resolution, providing unprecedented detail and data insight.
-
Product
Dynamic Test Systems
H3TRB | HTGB (HTGS) | RTGB (RTGS)
Test System
Durability and reliability of wide-bandgap materials such as SiC and GaN are an important topic. The focus here is on new failure mechanisms whose effects are not visible with traditional H(3)TRB/HTGS – but which nevertheless have an influence on the real application.
-
Product
Luminescence Defect Inspection System
INSPECTRA® PL Series
-
This system uses luminescent images created using photoluminescence (PL) to perform high-speed, high-sensitivity automatic inspection for crystal defects, cracks, and luminescence defects which cannot be detected with conventional visible light surface inspection!
-
Product
VLSI Test System
3380
Test System
The 3380 VSLI test system equipped with a maximum of 1280 I/O channels, 256 VI sources, flexable architecture and comprehensive optional function boards (ADDA/Hi-voltage DPS) can meet the high parallel multi-test tendency.
-
Product
Optics Test Systems
Scientific Instrument Engineering
-
Optik Elektronik Gerätetechnik GmbH
Development, design, manufacture and assembly of opto-mechanical assemblies and complete devices, including software.
-
Product
Optically Isolated Measurement System
IsoVu
-
IsoVu offers complete galvanic isolation and is the industry’s first measurement solution capable of accurately resolving high bandwidth, low voltage differential signals in the presence of large common mode voltages. The stand out feature of IsoVu™ is its best in class common mode rejection across the entire bandwidth. Accurate differential measurements rely on a measurement system’s bandwidth, rise time, common mode voltage, common mode rejection capability, and the ability to connect to smaller test points to characterize devices that are shrinking in size and increasing in performance. Despite these requirements, advancements in test and measurement for power testing, EMI testing, ESD testing, and remote measurement capability have been minimal at best and have not kept pace with changing requirements. While differential voltage probes have had modest performance gains in regard to bandwidth, these probes have failed to make any substantial improvements in regard to common mode rejection, and connectivity. IsoVu is a leap forward in technology and is the only solution with the required combination of high bandwidth, high common mode voltage, and high common mode rejection to enable these differential measurements.
-
Product
Fiber End-Face Inspection Interferometer
CLEAVEMETER 3D
-
The CLEAVEMETER 3D™ is a non-contact interferometer designed for inspecting the end-faces of cleaved or polished optical fibers with cladding diameters of 125 µm to 1200 µm. It gives immediate and precise information on important end-face properties such as flatness, perpendicularity, hackles and dust. Based on the NYFORS CLEAVEMETER 3D™ design, in addition to producing sharp fringe patterns it also generates three-dimensional images of the cleaved fiber end.
-
Product
Test Automation System for Driveline Testing
STARS Driveline
-
STARS Driveline is an integrated automation, acquisition and control system that provides a broad range of application functionality in a single, powerful environment. It has been designed to fulfil the specialist requirements and applications for driveline testing from simple modal testing on two or four wheel drive systems, to RLS simulation or advanced applications such as service load replication (SLR).
-
Product
Inspection Systems
-
Video Inspection Systems with?or without measurement capabilities are an excellent way to evaluate and test small items or items in?difficult to access locations. Many options are available in addition to the measurement capability. Video Inspection is used for a variety of purposes including the ability to see? and measure items that are much smaller than the eye can see or that hand tools can measure. Video systems can also reduce the eye and/or back strain associated with production environments where an operator must look in a microscope all day.
-
Product
Range Automation System
ELE-RAS
-
NSI-MI’s Range Automation System (ELE-RAS) has been specially designed to automate the time-consuming tasks associated with antenna range reconfiguration. This system eliminates operator intervention for range reversal, band switching, and power level optimization in antenna measurement facilities. This hands-off approach reduces uncertainty, extends the life of sensitive components, reduces RF leakage, and dramatically increases throughput and productivity. The modular architecture allows each ELE-RAS system to be optimized for maximum performance. ELE-RAS is software and receiver agnostic, meaning that it can be used to improve efficiency in virtually any antenna test range. Standard solutions are available for 20 GHz and 50 GHz applications. The ELE-RAS architecture also supports custom solutions to meet your unique measurement challenges.
-
Product
Single 4 Ch Fiber Optic Multiplexer
40-810-114
Multiplexer Module
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or mult- mode fiber.A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
SAS Protocol Test System
Sierra M124A
Test System
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
-
Product
Optical Protection System ( Single Fiber Two-Way )
OPS-1000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OPS-1000 Optics Protection System product series, mainly applies to optical communication field of single fiber two-way for main, light path switching equipment. It makes up from light path switching unit, optical power monitoring unit and network management terminal. In optical communication networks, OPS-1000 real-time monitor the optical power of operating fibers and spare fibers, when monitor the optical light path’s optical power is lower than setting switching threshold, it will alarming prompt and switch to the spare fiber to realize the line protection of optical transmission system.
-
Product
Brinell Optical Systems
-
Newage Testing Instruments, Inc.
Newage offers optical solutions for your hardness testing include the popular B.O.S.S. Brinell Optical Scanning System, HiLight optical scope and pocket optical scope.
-
Product
Fiber Optic Sensors
-
Achieve highly reliable and precise fiber optic sensing. Advanced Energy’s Luxtron® patented FluorOptic® temperature measurement solutions and WaveCaptureTM Fiber Bragg Grating (FBG) sensing solutions feature many options to meet your application needs.
-
Product
Optical Fiber
10 Gbps SFP+
-
Are designed for 10 Gbps serialoptical interfaces for data communications with multimode fiber (MMF).
-
Product
Power System Automation
-
Schweitzer Engineering Laboratories, Inc.
Automate your power system with SEL instrumentation and control devices. Substation automation uses data from IEDs, control and automation capabilities within the substation, and control commands from remote users to control power system devices.
-
Product
Automated Soil CO2 Flux System
LI-8100A
-
A portable, automated system for simple and reliable survey and long-term measurements over a study site. The LI-8100A Analyzer Control Unit contains an infrared gas analyzer and a connection panel to interface with the 8100-103 Survey Chamber, the 8100-104 and 8100-104C Long-Term Chambers, additional gas analyzers, and the LI-8150 Multiplexer.
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
