-
Product
High Impedance Active Probes
7A
-
An unterminated version, can be used for capacitance and resistance measurements or in low to medium speed signal applications where a 50 ohm termination is not required. A flexible coaxial cable length of 6 feet in length is standard on the Model 7A; however, when used for capacitance measurements, GGB Industries, Inc., recommends using a shorter 3 foot cable. If a shorter length of cable is desired for capacitance measurements, please specify it when ordering (Model 7A-3ft.). Please note that Model 7A uses Model 7 replacement tips.
-
Product
HPA-50 General Purpose Probes
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 590Overall Length (mm): 14.99
-
Product
HPA-0B General Purpose Probes
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
Product
µHELIX® Test Probes
Series S200, S300, S400, and S500
-
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.
-
Product
P2247-1W General Purpose Probes
-
Current Rating (Amps): 20Average DC Resistance lower than (mOhm): 10Test Center (mil): 225Test Center (mm): 5.72Full Travel (mil): 300Full Travel (mm): 7.62Recommended Travel (mil): 200Recommended Travel (mm): 5.08Overall Length (mil): 1,145Overall Length (mm): 29.08
-
Product
Near Field Probes
-
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
Product
Scanning Probes
-
Scanning probes can acquire several hundred surface points each second, enabling measurement of form as well as size and position.
-
Product
Fiber-Optic Probes
-
Designed with an unparalleled optical quality finish, Optomistic Products has developed a wide array of Fiber-optic Probes to accommodate your specific LED test requirement and mechanical constraints.
-
Product
Wide-Aperture Fiber-Optic Probes
-
Wide-aperture Fiber-optic Probes and Very Wide-aperture Fiber-optic Probes are used to test dim or misaligned LEDs.
-
-
Product
Temperature Probes
-
Is a device, typically, a thermocouple or RTD, that provides for temperature measurement through an electrical signal. A thermocouple (T/C) is made from two dissimilar metals that generate electrical voltage in direct proportion to changes in temperature.
-
Product
RF Field Probes (LSprobe)
-
Your product descThe LSProbe range of laser-powered E-Field probes offers precision, speed, and flexibility for EMC testing environments that demand reliable, uninterrupted measurements. These compact, battery-free probes use a galvanically insulated laser power supply, eliminating downtime and enabling continuous, high-resolution field monitoring with minimal noise and fast pulse response.ription goes here.
-
Product
Digital Inspection Probes
DI-1000
-
The ergonomically designed DI-1000 is Lightel’s all digital video microscope probe. It connects directly to your PC through the computer’s USB2.0 port. Featuring easy single finger focusing, a built-in image freeze/capture button, and detectable resolution to 0.5µm, the DI-1000 package includes our free ConnectorViewTM (standard) software, providing digital zoom, image display, image capture, auto-calibration and basic analysis tools.
-
Product
DDR4 MSO Probes
-
The DDR4 DIIM and SO-DIMM Mixed Signal Interposers connect Address, Command and Control signals of a DDR4 bus to the Keysight V-Series Oscilloscopes with the MSO option. These interposers also provide accessibility to DDR4 signals for convenient analog probing. The user can then easily observe both the digital and analog representation of the DDR4 Address, Command and Control bus. Solder down N5541A analog probes purchased separately from Keysight Technologies.
-
Product
SMD Test Probes
-
The Parrot Clip, model PCM W1 or PCS-MB W1 invention can be connected to resistance’s, diodes, integrated circuits (SOIC, SO) etcThe advantage of the Parrot Clip is given by the double metal connection made between the new metal tip and the steel hooked rod, spring loaded. This connection, being made by metal parts is electrical and mechanical reliable, even if the contact point are small. Connections are resistant even at high temperatures.
-
Product
Logic Probes
-
Logic probes are used to analyze the logic states (high/true: logic 1 or low/false: logic 0) of digital signals. To verify and debug today’s high-speed, low-voltage digital signals, you need logic probes that can accurately acquire signals from a wide variety of electronic designs, while protecting signal fidelity. Tektronix logic analyzer probes contain a variety of connectivity options that are engineered to ensure that signal acquisition is a true reflection of your design's performance. Compare and learn more about Tektronix logic analyzer probe solutions below.
-
Product
Linear Polarization Resistance Probes
-
Linear polarization resistance (rosion probes are commonly used in the water treating industry and other environments where instantaneous, on-line corrosion rate readings are required. Linear polarization probes are ideally suited to monitor fluctuations that may occur within a system; for example, these probes can be used to monitor corrosion inhibitor effects on a regular basis.
-
-
Product
Interface Probes
-
Low resistance used in: *ICT Testers *Functional Testers *Special Purpose Machines
-
Product
CP-059-026 Battery Probes
-
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 57Full Travel (mm): 1.45Recommended Travel (mil): 40Recommended Travel (mm): 1.00Mechanical Life (no of cyles): 100,000Overall Length (mil): 221Overall Length (mm): 5.61
-
Product
Near Field Probes 1GHz - 10 GHz
SX set
-
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Touch Probes And Vision Systems
-
HEIDENHAIN offers universal, high-accuracy touch probes for machine tools, enabling exact tool measurement, edge measurement on parts, and more. Proven technologies, such as wear-free optical sensors, collision protection, and integrated cleaning blowers, make these touch probes a dependable asset for tool and part measurement. The vision systems from HEIDENHAIN can also be conveniently deployed to monitor tools for even greater process reliability.
-
Product
Probes & Test Leads
-
The Di-LOG range to test leads are designed and manufactured to the highest quality and meet all safety standard as stipulated in BS EN 61010
-
Product
P2262A General Purpose Probes
-
Current Rating (Amps): 3Average DC Resistance lower than (mOhm): 30Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 90Full Travel (mm): 2.29Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 710Overall Length (mm): 18.03
-
Product
High Frequency Cartridge for HFP Series Probes
PACC-MS003
-
High Frequency Cartridge for HFP Series Probes
-
-
Product
Small Aperture Fiber-Optic Probes
-
Small-aperture Fiber-optic Probes are best for testing closely-spaced LEDs. With an aperture of 1mm, and a diameter of 1.2mm/0.050 inches, they can test LEDs spaced as close as 0.050 inches on center. Small-aperture Fiber-optic Probes are available with straight or right-angle stainless-steel tips as shown below. This allows for precise customization to your mechanical constraints.
-
Product
Optical Probes - Low Bandwidth
-
Depend on Tektronix to provide you with performance you can count on, and industry-leading service and support.*Broad Wavelength Response 500 to 950 nm or 1100 to 1700 nm*High-bandwidth DC up to 1.2 GHz*High Gain 1 V/mW*Low Noise <11 pW/√Hz*Probe Connects to DPO7000*1 and DPO/DSA/MSO70000*2Series*SONET/SDH and Fibre Channel Reference Receiver Performance
-
Product
RF Coaxial Probes & Probe Positioner
-
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
Product
Switch Probes
-
Switch point flexibilityDesigned for long life and reliable performanceVariety of tip options
