Clips
afix test lead to UUT, DUT or component.
See Also: Kelvin Clips, Alligator Clips, DIP Clips, IC Clips, Test Clips
-
Product
Low-Voltage Twin-Lead Tester
69134
-
Tests 5-50 volt, AC or DC circuits and components.Built-in lamp glows if circuit is live.Each of the 4-1/2'' (114 mm) test leads has an alligator clip on the end.Handy pocket clip.
-
Product
Slotted Side Clip, 160 Pin Connector
40-969-103
-
The 40-969-103 Slotted Side Clip may be needed where a screwlock is integral to the DIN 41612 connector. The slot enables the side clip to be inserted under the screwlock head, allowing an adjacent connector to be secured.
-
Product
Electrical Tester
PRO T6-1000
-
The T6-1000 PRO Electrical Tester measures voltage up to 1000 V ac and current up to 200 A ac, all through the open fork and without test lead contact to live voltage. Connect the black lead to ground with the included heavy-duty alligator clip, slide the wire into the open fork and see both voltage and current at the same time. On wires up to AWG 4/0 (120 mm2), carrying as much as 200 A and 1000 V ac. Even with gloves on. It will change how you do your job.
-
Product
Static Axial Clip-On Extensionmeters
2630-100 Series
-
The Instron static axial clip-on extensometer delivers precise strain measurement for static tests by quickly clipping to specimens (metals, plastics, composites) with minimal attachment force. Its rugged cross-brace design resists distortion, includes built-in over-extension protection, and meets ASTM E83 / ISO 9513 standards — making it a reliable, high-accuracy option for general and temperature-controlled testing.
-
Product
51-Pin REDEL High Voltage Cable Assembly, Male To Unterminated, Ferrules, 0.25A, 1m, 29 Wires
A051KMR-F-HA100-29
-
This is a 1m long male to unterminated 51-Pin REDEL high voltage cable assembly with ferrules constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips areprovided to secure the connector to associated product.
-
Product
DC Detector
-
This sensor can be used to troubleshoot any DC circuit with voltage ranging from 6-50 volts DC. It features an audio and visual alert and a sharp, rust-proof, stainless steel tip that works great for penetrating insulated wires. This sensor also features an extended ground lead with an extra-large alligator clip to ensure a good connection.
-
Product
Plunger Clip
BU-00201-0
-
Plunger clip • Material: Cap & Body: glass filled nylon; Spring: Stainless steel; Contact: beryllium copper; insulator to a single contact point • Length: 1.75” (44 mm)(BU-00201-*); 2.50” (63 mm)(BU-00202-*); 3.50” (88 mm)(BU-00203-*); • *Std Colors: -0 Black -2 Red • Rating: 1000 Volts, 10 Amps.
-
-
Product
3 Digit LED Voltmeter
SP 300
-
The SP 300 is a 3 digit LED voltmeter with 9mm (0.36") digit height. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into an 8-way SIL socket and can be fitted into a panel via the fixing clip. Splashproof protection to IP65 is achieved by fitting the seal supplied.
-
Product
Kelvin Clip Test Lead Set
5940
-
Kelvin Clip Test Lead Set. Ideal for resistant measurementsbelow 1 ohm.
-
Product
Tone Generator
140BMC/6P
-
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a.Clear line. b.Busy line. c.Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
Product
Electronic Test Lead Kit
U8202A
-
Designed for use with the U3606A DMM and DC power supply; includes leads, alligator clips, mini grabbers, and more
-
Product
Thyristor Surge Suppressor (TSS)
-
When protecting parallel (double) circuit transmission lines, devices have two main functions in transient mode: clipping the voltage and drifting the current due to overload.
-
Product
Cost-Effective ATE System
PRO RACK ATE
-
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
Product
Limiters
-
A limiter catches the loudest peaks of an audio source and applies brick wall compression that prevents it from exceeding the clipping point of 0 dBFS.
-
Product
LED Probe Clip Light
U1176A
-
Clip this 3-in flashlight on your test probes for great visibility when using your handheld DMMs in dark places
-
-
Product
Accessories
-
Every Logic ships with a case, usb cable, wire harness and test clips. Get extra stuff here.
-
Product
Alligator Clip Leads
U1781A
-
The Keysight U1781A is to be used with the U1700 Series Handheld Capacitor and LCR meters. These clips are shipped as standard with every handheld capacitor or handheld LCR meter.
-
Product
Operational Historian Software
-
It is time to retire the warn-out clip boards and tedious transcription of critical plant performance data. FactoryTalk® Historian software captures operational process data from multiple sources at lightning speed. You gain a supreme level of supervisory control, performance monitoring and quality assurance with robust FactoryTalk Historian software that can scale from machine to enterprise. Reliably recording time-series records at this pace would be impossible, even for your most caffeinated plant-floor record keeper. FactoryTalk Historian dashboards take that work off your hands. Plus, the added confidence in forecasting trends with reliable data will generate new level of productivity. So long, clip boards. You won’t be missed.
-
Product
Tone Coax Cable Generator
240 HAL
-
The AINES 240 HAL Tone Generator is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
Product
Bed of Nails Test Clips
142-2
-
These multi-purpose test clips are a great way to tap live readings. Unique micro pins cause less damage, should you decide to pierce the wire's insulation.
-
Product
80-250V AC/DC Voltage Tester
1931
-
Peaceful Thriving Enterprise Co Ltd
*Handy pocket clip.*With cETL Approval.*Bright neon indicator.*Insulated housing and test leads.*Check voltage on 80-250V AC/DC.
-
Product
Surface Mount-to-DIP JEDEC SOT-25, SOT-23A-6 Adaptor
1110748
-
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
Product
Lifetime Heavy Duty Circuit Tester
27000
-
Checks 6 and 12 volt systems. Heavy duty battery clip. 5' of tough, flexible, heavily insulated rubber wire. Designed to withstand the most rugged use.
-
Product
Mag Lead w/Alligator Clips
138
-
*54" Test Lead Set *Mag Lead features a magnetic disconnect. *You can "stick" to any metallic ground or test point. *Time saving product - can substitute for alligator clips at metallic test points. *Now, when you need alligator clips, you've got them! *Fits almost all DMM's and hand held scopes. *Get the Mag Lead, it stays put and won't fall off!
-
Product
Mini SMD Grabber® Test Clip Lead With 4mm Jack
72929
-
Mini SMD Grabber Test Clip Lead with 4mm Jack
-
Product
USB Tester 2.0
TLS-0050
-
The USB Tester will make it a snap to monitor voltage levels and current usage without having to re-wire your breadboard. Just connect to your oscilloscope or DMM test leads, and you're good to go! The USB Tester has both banana clip sized drills and standard 0.1" headers. When you are not testing current you can add a jumper for normal operation. The USB D+/D- pins are also broken out so you can monitor those on an oscilloscope, or for USB sniffing.
-
Product
"Handy Hooker" Circuit Tester
25600
-
Small size allows easy use even in the tightest places. Quickly test low voltage up to 12 volts. Alligator clip grounds tester.
-
Product
Minigrabber® Test Clip For Max. .090" Wire Dia, Do-It-Yourself
3925
-
Minigrabber? test clip for max. .090" wire dia, Do-It-Yourself, available in ten colors
