Instrument Cables
Are precision cabling for instrumentation.
See Also: Instruments, Modular Instruments, Cable Assemblies
-
Product
Digital Test Instrumentation
EDigital-Series™
-
Teradyne’s eDigital IVI driver controls all parallel digital functional test parameters, including per-pin timing, data formats, pattern data, and timing alignment on 64 channels (32 static + 32 dynamic or 32 differential)—each with an 8M pattern depth and results memory.
-
Product
Instrument Bracket Kit, Receiver, Slide Configuration, For 28" And Longer
310113507
-
Instrument Bracket Kit, Receiver, Slide Configuration, for 28" and longer.
-
Product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
-
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
VXI 12-Channel Digital-to-Analog
65DA2-55
-
NAI’s 65DA2-55 is a 12-channel Digital-to-Analog Instrument on a VXI board. This single-slot, message-based board provides twelve independent, single-ended, 16-bit, Digital-to-Analog (D/A) channels.
-
Product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
-
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
Product
VB-8012, 2-Channel, 100 MHz Bandwidth VirtualBench All-in-One Instrument
783555-01
-
2-Channel, 100 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8012 combines a two‑channel, 100 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
Product
EV-DO Analysis Using NI PXI RF Test Instruments
NI-RFmx EV-DO
-
Highly optimized RF measurement experiencePerform physical layer analysis on EV-DO cellular signals including MODACC, ACPR, CHP, OBW, and SEMSimple access to advanced measurement parallelism
-
Product
64-pin Matrix Card
E8783A
-
The Keysight Technologies, Inc. E8782A pin matrix with instrumentation and E8783A pin matrix card are new additions that double the number of supported channels offered by the previous E8792A and E8793A matrix cards. With this increase in supported channels, customers can now support tests on units with a higher number of pin counts using the E6198A switch/load unit. Effectively, the E8782A pin matrix with instrumentation is configured with 24 instrument channels and 40 measurement channels and retains the features included with the older E8792A card.
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
-
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
Product
Instrument Bracket Kit, w/ Strain Relief, Slide Configuration, for 28"+ Slide Kits
310113002
-
Instrument Bracket Kit, w/ Strain Relief, Slide Configuration, for 28"+ Slide Kits Similar to instrument bracket p/n 310113453, but includes cutout to accommodate air intake on NI PXIe-1088 chassis. Only compatible with slide configurations 28" and longer. Not compatible with cable tray. Not recommended for use with 2+ tier 90 Series systems (905, 9075, etc.).Used to mount testing instrument to slides and also allows test instrument to slide out for maintenance access. Provides strain relief in front area of bracket. Compatible with chassis (see drawing for more information)
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Ferrules, 2m, Screwlocks
A068SFR-F-6B200
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Female, 0.5m, 90º
A1604FT-1604FT-0A050
-
For applications where a 90 degree down cable exit would be preferred. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connectors to have a second fixing then the connector can be fitted with the optional screwlock assembly 40-969-101 where applications permit.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated to Tinned Ends, 1 Amp, 2m length, 500 Port
A500RMR-T-1B200
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to to products using the 500-Pin SEARAY connector.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 1m, HV
A037DF4-C-HA100
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
20-Pin GMCT Cable, Male to Female, 10A, 1m
A020GMR-020GFR-0B100
-
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
GMCT 26-Pin RF Cable Assembly, 75Ω, Male To Unterminated, 2m, RG179 Cable
40-979-726-2m-FU
-
This 2m long cable assembly is part of a range of cables suitable for applications using the Positronic 26-pin GMCT 75Ω RF connector. It is constructed from RG179 silver plated copper clad steel cable with FEP insulation and a bandwidth of 500MHz. Screwlocks are provided to secure the connector to the associated product.
-
Product
SHC68-NT-S, 68-Pin VHDCI Female to 68-Pin Bare Wire Male Multifunction Cable
189041-02
-
SHC68-NT-S Shielded Cable for 7831R boards, 68-pin VHDCI to unterminated, 2m
-
Product
Cable Assembly, 160-Pin DIN41612, Male to Male, 0.5m
40-970-160-0.5m-MM
-
The cable assembly is not suitable for direct connection to Pickering Interfaces switching products.
-
Product
RS485 Null-Modem Cable, DB-9 Female to DB-9 Female, 1m
183283-01
-
9-Pin Female DB-9 to 9-Pin Female DB-9 Serial Cable - The 9F-9F Serial Cable, sometimes referred to as GPIB Serial Cable, connects and controls GPIB devices using RS232 and RS485 serial ports. The 9F-9F Serial Cable is offered in different lengths.
-
Product
Type-A USB 2.0 Male to Type-B USB 2.0 Male USB Cable
784387-02
-
The USB-A to USB-B Cable provides data, communication, or power connectivity between compatible hardware. You can use the USB-A to USB-B Cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB cables. This cable is available in various lengths.
-
Product
Cable Assembly, Receiver, 36", Micro Power & Micro Coax, 17 MCX Plugs
540338010247
-
Cable Assembly, Receiver, 36", Micro Power & Micro Coax, 17 MCX Plugs
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m HV, Exit Towards Pin 1
A050DF5-C-HA050
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
20-Pin GMCT Cable, Male to Unterminated, Ferrules, 10A, 0.5m
A020GMR-F-0C050
-
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 0.5m, Screwlocks
A068SMR-T-6B050
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
8-Pin D-SUB Female To 8-Pin D-SUB Female Switch Cable
781092-01
-
The DB8F-DB8F-40A helps you connect to the PXI-2512, PXIe-2512, PXI-2514, and PXIe-2514 PXI Signal Insertion Switch Modules. You can use this cable to facilitate signal routing between instruments and devices-under-test (DUT).
-
Product
68-Pin VHDCI Cable Assembly, Male to Unterminated With Cut Ends, 1m
A068VMR-C-6C100
-
The male cable assembly is suited for direct connection to various products using the 68 Way VHDCI connector.
-
Product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Tinned Ends, 0.5m
A009DM5-T-0A050
-
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation.
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 200 Pin Male LFH with M3 Jackscrews
540105020205
-
Cable Assembly, Receiver, TriPaddle, 36", 200-Pin Male LFH with M3 Jackscrews
-
Product
Low Noise Test Cables For N1413 With B2980 Series, 3m
N1427B
-
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
Product
50Ω UWave SMA 2.4 Cable Assembly, 50GHz, 0.5m
40-977-545-0.5m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
