Electric Vehicle Test Systems
See Also: EV Test Systems, Electric Vehicle
-
Product
Test Automation System for Heavy-Duty Engine Emission Testing
STARS HDEET
-
STARS HDEET is a Heavy-Duty Engine Emission Test application available as an optional extension to STARS Automation. It provides efficient test cycle execution, emissions equipment control, results calculation and reporting, in compliance with the different legislative standards. Its flexible design offers a wide range of customization while addressing the various requirements for research and development, conformity of production, and certification testing.
-
Product
Smart Electric Tester
SET-12
-
The SET-12 Tester is a portable device for measuring electrical parameters. Unique combination of the most needed measurements into one device allows for a quick diagnosis of faults.
-
Product
Wafer Level Multi-Die Test System
ITC55WLMD
-
The ITC55WLMD series of test systems has been developed by ITC to be stand-alone UIL test systems configured specifically to test on wafer. The systems include an ITC55series UIL tester and inductor box, a current limiter module and a system controller
-
Product
Information Warfare/ Electrical Warfare Training
-
Stratign’s training programs are designed considering the latest challenges faced by governments, LEAs, intelligence agencies. We provide training which are tailor-made and customised for the customers based on their level of understanding.
-
Product
Electrical Testing
-
Innovative Testing Solutions, Inc.
Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.
-
Product
DynoLAB Test Cell Supervisory System
-
SAKOR Technologies’ DynoLAB™ data acquisition and control systems offer reliable, cost effective automation of all types of dynamometer test systems. As with all SAKOR products, the DynoLAB system undergoes a continuous program of upgrade and improvement, regularly expanding and enhancing DynoLAB’s capabilities.
-
Product
Short Circuit Test System
-
Shanghai Guantu Technology Co., Ltd.
The short-circuit test system refers to what kind of short-circuit test is carried out by which equipment, and how long is the test time. But I have one thing to tell you, the short circuit test is a kind of destructive test, mainly to test the working condition of the used equipment in a crisis situation, or to test how strong the anti-destructive ability of the used equipment is. Just like a lot of equipment in the military must undergo a short-circuit test, some for 3 minutes or longer, in order to resist breaking calls against the enemy during wartime.
-
Product
Vehicle Interior Air Quality Testing
-
Underwriters Laboratories Inc.
Hundreds of volatile organic compounds (VOCs), which off-gas from the materials and finishes used in car interiors, can be present in the air inside a new vehicle. VOCs can cause odor complaints and have been linked to numerous health concerns. As the demand for healthier products increases, vehicle manufacturers that tell a compelling sustainability story can capitalize on a significant opportunity to grow market share. UL helps manufacturers capture value for their sustainability efforts, mitigate risks and comply with increasingly complex regulations.
-
Product
Electrical Safety Testers
STW-9900 Series
-
* 500VA AC Test Capacity* 240 x 64 Ice Blue Dot Matrix LCD* Manual/Auto Mode* Function Key for Quick Selecting* High Intensity Flash for Caution & Status Indication* Safety Interlock Function* Zero Crossing Turn-on Operation* Zero Crossing Turn-on Operation* True RMS Current Measurement * High Resolution : 1μA for Measuring Current, 2V for Setting Voltage* PWM Switching Amplifier to Enhance the Power Efficiency and Reliable Testing* Max. 100 Memory Block for Test Condition (Step) Setting. And Each Step can be Named Individually* Remote Terminal on the Front Panel for“Start”and“Stop” Control by External* Interface: RS-232C, USB Devise, Signal I/O and GP-IB (Option: OPT.1)
-
Product
Functional Test Systems
-
Acculogic offers commercial functional test systems for a broad range of manufacturing test applications, including automotive and military-aerospace.Designed for production testing, our solutions are optimized for throughput, reliability, repeatability, and cost
-
Product
Photovoltaic and Electrical Installation Testers
-
Photovoltaic electrical installation safety testing is a special area of electrical installation safety testing as it also entails tests and measurements on DC systems, which are relatively uncommon in most domestic, commercial and to a certain extent industrial environments. There is also the addition of photovoltaic-specific tests that are outside the realm of standard test and measurement procedures.
-
Product
Halo Automatic Testing System
-
Our revolutionary Halo system is an automatic metal detector testing device. It is designed to automatically test ferrous, non-ferrous and stainless steel samples on all Fortress metal detectors. Automatic testing saves time, money, labor, along with removing the risk of human error and work place injury at critical control points on a manufacturing line while complying with industry standards. The Halo system is ideal for applications where manual testing of a metal detector is made difficult due to access, position, access to the product flow, environmental conditions, etc.
-
Product
Sound Velocity, Temperature and Pressure for Underwater Vehicles.
UV-SVP
-
Designed for Underwater Vehicles where space is at a premium, the UV-SVP is based on the Valeport miniSVS. Incorporating Valeport’s class-leading time of flight sound speed sensor, a PRT temperature sensor and a 0.01% pressure sensor in a compact package weighing just 750 grams (in air), the lightweight titanium housing gives a depth rating of 3000m. A wide range (9-30V DC) isolated power supply and RS232 communications complete the package.
-
Product
Compact EMC Test System
Multi-CE5
-
The Multi-CE5 includes an Electrical Fast Transient Generator (EFTG), a Combination Wave Generator (CWG) and a Coupling-/Decoupling Network (CDN) for single-phase power supply lines. The software program CE-REMOTE allows full remote control of the test generator via Ethernet light guide as well as recording, evaluation and documentation of test results, according to IEC 17025. To record the wave shape of impulses, it is equipped with an Impulse Recording Function (IRF).
-
Product
Three-phase Fully Automatic Test System
TS41
-
Calmet Smart Calibration Devices
The Calmet TS41 test system consists of a three-phase reference meter of accuracy class 0.02% (or 0.04%) and an integrated three-phase current and voltage source up to 3x120A/600V. It makes possible automatic testing of electricity meters in meter test stations
-
Product
Electrical Tester
T6-1000
-
The Fluke T6-1000 Electrical Tester with FieldSense™ technology lets you quickly, safely take True rms voltage and current measurements without test leads.
-
Product
Backplane Test System
402HV
-
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Product
Mezzanine System
3560
System
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
Product
Pneumatic Horizontal Shock Test System
KRD12 series
-
The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
Product
Automated Test Systems
-
Chroma Systems Solutions, Inc.
From power conversion to battery to electrical safety, our test systems will maximize your time, improve your validation process, and increase your throughput.
-
Product
Intraocular Lens Optical Test System
OptiSpheric® IOL R&D
-
The OptiSpheric® IOL R&D is specially designed for the analysis of single intraocular lenses in research and development. With the OptiSpheric® IOL R&D, important parameters of all types of lenses (monofocal, multifocal, trifocal, toric, aspheric and those with extended depth of focus (EDOF) – whether diffractive, refractive or sectors) can be measured and tested in air or in situ in accordance with ISO 11979.
-
Product
Meter Test System
MTS-100
-
Kongter Test & Measurement Co., Limited
This Meter Test System features state-of-art designing with high accuracy. It is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 120A). This system is particularly designed with modular structure for calibration and test of different single phase/3 phase electronic/inductive active and reactive energy meters.
-
Product
Multifunctional Electrical Installation Testers
Eurotest XA
-
The fifth generation of Metrel's multifunction electrical installation testers brought know-how in the testing procedures to reality. Because of the need to be efficient, faster and competitive but still responsible and concentrated on safety, all the technical content and innovations under AUTO SEQUENCE, rotate around taking care about testing procedures itself.
-
Product
Ultra-sonic Test System
V-Meter
-
The V-Meter is an advanced ultrasonic, pulse-velocity test system widely used for quality control and evaluation of concrete structures. It can identify non-homogeneous conditions such as voids, cracks, honeycombs and frozen concrete.
-
Product
Meter Testing System
ASTel
-
Three-phase Meter Test Equipment of ASTeL 3.2x.x series system is a fully automatic system enabling simultaneous, multi-position calibration and legalization of electric energy meters. The automatics include power sources, reference standards, stand controllers, photoelectric scanning heads, separating transformers, and other elements of the system. All these elements are controlled through a Windows based executive program.
-
Product
Integrated AI-ADAS ECU And Cameras For Large Commercial Vehicle
ADM-TJ30
Electronic Control Unit
The integrated AI-ADAS ECU is connected to 8 cameras and powered by the vision-AI algorithm. It can detect and classify different kinds of vehicles/ pedestrians/ two-wheeler riders/ lane marking and other objects to perform multiple ADAS functions.
-
Product
Electrical Fault Detector
-
Our product range includes a wide range of Electrical Fault Detector and 0.36W Electric Fault Detector.
-
Product
(250 kN) Fatigue Testing System
8802
-
The Instron 8802 is a high stiffness, 250kN fatigue rated servohydraulic testing system that meets the challenging demands of both static and dynamic testing requirments. The 8802 systems include a range of configurations available to provide complete testing solutions to satisfy the needs of advanced materials and component testing. The design of the 8802 frame makes it ideal for installation within a laboratory environment, generally without the need for strangethened floors or raised ceiling heights.
-
Product
Multi-Purpose RF Test System
SPA441
-
The S - Series multi-purpose RF test system can be used in many applications such as R&D lab, ATE factory testing, EMC testing, field testing, and general purpose RF design. The S - Series is a flexible alternative to expensive and bulky RF test equipment. As shown in the setup in the upper right the S-Series system can be utilized to simultaneously provide all RF functions using its 7 inch front panel display or can be connected to a larger monitor for ease of viewing multiple windows at the same time
-
Product
Gel Strength Test System
LD-LGST-A10
-
Gel Strength Test SystemLD-LGST-A10is mainly used to measure the gel strength of gelatine under the stipulated environment. It has traveling accuracy ± 0.3 % and Test range up to 5 to 1000 g Bloom. It consists of Jelly Strength Tester, Constant Temperature Bath and Refrigerator. Sampling depth can be present arbitrarily in 1 to 60 mm. It consists four kinds of sampling measurement modes: single-step, maintaining, circulating and automatic.
