-
Product
EBIRST 9-pin Male D-type Termination Fixture
93-003-103
Termination Fixture
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,50 kg
-
Product
µHELIX® Test Probes
Series S200, S300, S400, and S500
-
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.
-
Product
ATE Self Test Fixtures
AL663
Test Fixture
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
DC Power Module, 20V, 15A, 300W
N6773A
Power Module
The Keysight N6773A is a 300 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
Supported Test Systems
-
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/GR2270/71
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,00 kg
-
Product
In-Circuit Testing
-
If you are looking for in-circuit test applications, equipment or advice, our experienced engineers can help you. Whatever your fixturing requirements or special software features, our long history of work in this field means that we have probably seen and done it before.
-
Product
Lever Handle Bed of Nails Testers
Automator Manual Family
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
EBIRST 8-pin Male Power D-type Termination Fixture
93-012-103
Termination Fixture
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Peel Testers
-
Imada offers motorized peel testers in vertical or horizontal configurations.The motorized test stand, digital force gauge and peel fixture apply tension to a safety seals, tapes and laminates.Special attachments and fixtures facilitate 45°, 90°, 180°, ‘T’ and rotary peel tests.Motorized peel testers offer speed control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All peel testers with digital force gauges have data output capability for analysis by optional data acquisition software.
-
Product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
Test Fixture
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
Product
Tool, Solder Kit, Mini Coax with Solder Sleeve
910121144
Soldering Fixture
Used to solder Mini Coax Solder Sleeve contacts.
-
Product
EBIRST 104-pin D-type Verification Fixture
93-022-101
Verification Fixture
The 93-022-101 104-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Adjustable Press Plate Bed of Nails Testers
Prober Adjustable Family
-
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
Product
Dual Servo Electrical Test Fixture
TA-334001
-
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
-
Product
2m BNC Test Cable
16048D
-
The 16048D test leads extend the measurement port with a 4-terminal pair configuration. It provides a BNC female connector board to allow attachment of user-fabricated test fixtures.
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
-
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
Product
INTERFACE TEST FIXTURE KITS
GENRAD 2270
-
Test-X GR Series CAM/TRAC® kits offer the same "Z" axis motion as the standard CT Series with the advantage of interface compatibility.Standard features include locking handle assembly, 3/8" FR4 probe plate, and 12 position I/O block interface..
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-100 SERES
-
Test-X MT-100 Series mechanical kits are an inexpensive solution for testing smaller printed circuit boards and other devices.The MT-100 Series features a 1/2" thick FR4 probe plate and a 3/8" thick Lexan top plate. Precision alignment is assured through tooling holes in both the probe and top plates. Units are available with a 2-1/2" pan or an upper head assembly
-
Product
Boundary Scan Test
-
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
Product
MANUAL TEST FIXTURE KITS
SERIES 5590
-
Built with unique design features: Ease of assembly and disassembly All side panels are removable Side panel material is delrin for easy machining for connectors, switches etc.Light weight and durable construction2" Between Probe plate and lid plate allowing more room for tall board components
-
-
Product
Function Test Fixtures
-
Modulized UUT BFT Test Fixture, Multilevel BFT Fixture, Over Clamp Test Fixture, Rack Mount Test Fixture, Self Contained Pogopin Test Fixture, Simple Low Cost PCBA Test Fixture, Tight Seal Required RF F/T Fixture, and more from IST Engineering
-
Product
TRUE Z-AXIS CAM ACTIVATED TEST FIXTURE KITS
-
The Cam Press is designed to provide precise, bed-of-nails contact, in a production test environment. Durable aluminum and steel construction and precision bearings insure accuracy and repeatability sufficient to contact test points as close as 10-mils center-to-center.
