-
Product
CamTrac Z-Axis Test Fixture Kits
CT Serie
-
The CT Series Mechanical Kits, utilizing the patented CAM mechanism1, offset the same precision linear motion. The 'Z' axis motion is ideal for a larger point count mechanical test applications.The CT Series features a hinged 3/8" FR4 probe board, tooling holes for precision alignment, removable sides, precision shafts and cam slide block assemblies, and a pan latch assembly.
-
Product
PXI Expandable 16x16 RF Matrix 75Ohm SMB
45-720A-751
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
dmXLAN Software
-
This software can be used to configure all the ELC Nodes and Switches, as well as to monitor the dmXLAN network. Use it also to control and test lighting fixtures connected to the dmXLAN network, independent of the brand of consoles and lighting fixtures used.
-
Product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
-
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
Product
Test Fixture, Axial And Radial
16047A
Test Fixture
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
Product
Bottom Electrode SMD Test Fixture
16197A
Test Fixture
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
Product
Wireless Test Fixtures
-
At Forwessun, we have vast experience in designing and delivering wireless in-circuit test (ICT) fixtures. We have experience in providing fixtures tailored to the unique needs of various different industries. While our primary customer focus has been on full and half-bank fixtures for the HP3070 system, we offer bespoke solutions for other platforms as well including GenRad, Teradyne, and SPEA systems.
-
Product
RF-Ready DC Fixture
-
The RF-Ready DC fixture provides space for mounting RF input and output matching circuits. Hence, it is possible to tune up the assembly at a remote test station, such as a network analyzer, to peak performance and then run the life test with DC stimulus. The matching structures also allow incorporation of more complex stabilization structures.
-
Product
Compression Set Fixture
ASTM D395
-
ASTM D395 Compression Set Fixture is to test rubber under constant deflection in air.
-
Product
DC Power Module, 35V, 3A, 105W
N6744B
Power Module
The Keysight N6744B is a 105 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
Mach Airspeed Test Fixture
TA-6055A
-
The TA-6055A is a Mach Airspeed Test Fixture built to support the testing and repair of the 2082 and 2083 series of Servoed Mach Airspeed Indicators (SMASI) used in some Boeing aircraft. These mach airspeeds are synchro driven and require a coarse and fine input for altitude and a third input for airspeed. This test fixture was designed around the test procedure and is interfaced with our TA-1001 panel which provides for two of the synchro sources and two Angle Position Indicators (API).
-
Product
Clamshell Type Mechanical Fixtures
Series 34
-
The Series 34 Test Kits are a smaller 4 block version of the GR2270
-
Product
BMS Manufacturing Test System
Test System
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
Product
Laser Calibration System, Superior Accuracy, Portability and Reliability
5530
-
The configurable system offers all the components you need to perform a variety of measurements using the USB on your PC as the host controller and power source. For basic linear measurements you will need the USB Axis Module, USB Sensor Hub, Air and Material Sensors, Sensor Cables, Software, Laser, Laser Cable, Remote Control (optional)and the Linear Optics Set. Other available options include the Laser Tripod (with laser mounting plate), optics and fixturing kits for making additional types of measurements, and wheeled transit cases.
-
Product
Function Test System
Focus-FX
-
This is general function test system. User can change board model easily by replacing a test fixture and changing inspection program. We have variety of measurement instruments such as FX modules which can control commercial instruments. It is possible to add required modules into existing units as they are connected by USB port. User can expand as per desired inspection specification.
-
Product
Turn-Key Functional / Mechanical Fixture
-
In addition to In-circuit testing, functional testing is widely used in the industry to verify electronic cards. This is why ReMaTek has always paid a special attention to the specific requirements of functional testing. Our dedicated engineering staff is prepared to handle all of your mechanical, electrical and software requirements. We are aiming particularly the small turn-key test systems where all the elements; the mechanical fixture, the test equipment and the test software, are put together in a complete system.
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
PCI RF Switch Cards
-
These 8x9 RF Switch Cards are suitable for switching frequencies up to 500MHz. Available in either 50 or 75 versions with SMB coaxial connectors. These switch cards are intended for the easy construction of high-performance bidirectional matrix switching systems. Automatic isolation switches are located on all coaxial connections, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
Product
Topside Probing for Functional Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.
-
Product
Bi-axial Dynacell Load Cells
2527 Series
-
During tests carried out on servohydraulic machines, elements of the system are subject to acceleration. As a result, in addition to the force applied to the specimen, the load cell also reads forces resulting from its own movement and the mass of the grips and fixtures attached to it. Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages:*Reduces dynamic load errors which can be a significant percentage of reading *Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
Product
110 GHz, 1.0 Mm (m-f) Test Port Cable 10 Cm
11500JK10
-
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
Product
RF Chamber Fixtures
-
- 12” W x 12” D x 8” H internal dimensions- RF mechanical chamber can fit various wireless and Bluetooth products- test either commercial or consumer
-
Product
Adjustable Press Plate Bed of Nails Testers
Protector Adjustable Family
-
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Product
Burn-In Test Fixtures
-
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
Product
Aircraft Test Set
CA-2100S-07
-
The CA-2100S-07 is a bench mounted, modularized and computer based test set used to service all types of aircraft electronics. It simulates the aircraft environment and replaces a myriad of specialized test fixtures found in the industry.
-
Product
Custom Vibration Testing Fixtures
-
Paragon Systems is unique in being able to not only perform your vibration test, but also to design, fabricate and qualify your vibration testing fixtures. Usually all we need from a client is their vibration test profile, a CAD model and the GD&T of the DUT.
-
Product
Latch-on Test Fixtures
-
Latch-on Test Fixtures provide a convenient way for production personnel to quickly and reliably make electrical connections to a product for programming or final test. These custom fixtures eliminate the need to hand-wire products in order to power them up and communicate with them. Typical applications for latch-on test fixtures are metering devices, control panels, and any type of controls that connect via terminal strips.
-
Product
Wind Power Solution
ECO GE
-
The ECO GE is custom-made with firmware and fixtures designed specifically for GE 1.5x and 2.5x. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
ICT/FCT-Fixtures (Large IF)
GenRad CK-2-228X
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Resistivity Cell For N1413 With B2980 Series (26/50/76 Mm Diameter Electrodes)
N1424C
-
The N1424C is designed to operate specifically with the B2985B/87BElectrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424C to the B2985B/87B.
