Motion Controllers
Coordinate motion and timing.
-
Product
Z-Axis Drive and Controller
MFC-2000
-
Applied Scientific Instrumentation
The MFC-2000 has been specifically designed to provide a high resolution and highly repeatable, means of controlling the focus/Z position of the microscope stage. Precise control of the microscope's focus is obtained through the use of a closed-loop DC servomotor employing high resolution encoders for positioning feedback. By using closed-loop control of the focus position, there is no chance that the focus point can be lost as can occur with open-loop stepper motors.
-
Product
Programmable Limit Switches & Industrial Controls
-
Computer Conversions Corporation
Programmable Scale Factor16 High Current OutputsResolution to 1 in 4096Full Scale Zero OffsetNon-Volatile setpoint and Parameter Storage(EEPROM)Programs through zeroDigital Display of PositionTachometer (R.P.M.) DisplayResolver Connect DetectionRS 232 Program loading (option)300 Maximum program Setpoints with any Distribution over the 16 Outputs (1200 Optionally Available)Response time less than 5.1 microseconds
-
Product
2-Axis Stepping And Servo Motor Control Universal PCI Card
PCI-1220U
-
Independent 2-axis motion controlHand wheel and jog function2-axis linear interpolation function2-axis circular interpolation functionContinuous interpolation functionProgrammable T/S-curve acceleration/deceleration rateUp to 4 Mpps output for each axisTwo pulse output types: CW/CCW or pulse/directionUp to 1 MHz encoder input for each axisTwo encoder pulse input types: A/B phase or up/downConstant speed controlPosition management and software limit switch functionBoardID™ switch
-
Product
Advanced Data Acquisition And Control System
ADACS
-
This high-speed damage-control system was built around Arc Fault Detect and Continuous Thermal Monitoring (AFD/CTM) from the Johns Hopkins Applied Physics Laboratory. When AFD/CTM detects dangerous arc faults — powerful discharges of electricity between conductors — the ADACS system immediately cuts power to the affected circuit before it can damage equipment or injure nearby personnel. Altogether, the system prevents loss of life, preserves countless repair dollars and assures continuous readiness.
-
Product
Remote Control Voice Recognition Tester
BK3013
-
Ready to help you take on the leading edge of consumer technology, we have designed a machine that tests microphones which both use RF and are used for voice recognition. The BK3013 runs a uniform SPL sweep to calculate FRF and also runs an SPL sweep that allows you to test the SPL range of your mic. Our "Test Shop" program will show you the results in graphs and allows you to have the computer check specific points in the test.
-
Product
Drivers / Controllers
-
The LED Driver/Controllers incorporate fully integrated power solutions. Digital drivers and controllers provide programmable, fully integrated power solutions with fast response times.
-
Product
Communication and Control
-
Measure Tech designs and manufactures push button switches, volume controls (RVDT), and knobs for Airbus, Boeing and Bombardier aircraft.
-
Product
Mass Flow Controller for Low Flow
HFM-200 / HFC-202
-
The HFM-200/HFC-202 is Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers. Featuring reliability and stability, the 200 Series is chosen by OEM's for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-200 / HFC-202 meters and controllers have flow ranges from 0-10 sccm to flows of 0-25 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Many corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
Product
Controller
ServoEDGE
-
ServoEDGE is an integrated, multi-loop control and data acquisition system designed specifically for hydraulic and servo-hydraulic applications, including system modernizations, new installations, turnkey systems and complete test cell control and data acquisition systems. The system is designed and pre-configured using both NI PXI hardware and Genuen's integrated connector blocks and power module, which minimize cost and simplify connectivity and integration. The configured system provides a wide range of I/O capabilities for typical hydraulic applications; and since the system is based on off-the-shelf hardware, it can be easily modified to cover a wide range of I/O requirements.
-
Product
CAMAC Controller With USB Interface
CC-USB
-
The CCUSB is a full-featured CAMAC Crate controller with integrated high speed USB-2 interface and full CAMAC dataway display. It supports Master and Slave operations with complete CAMAC arbitration as well as auxiliary CAMAC controller operation.
-
Product
Wind Tunnel Control System
WTCS
-
Wind tunnel facilities are important for the development of all kinds of transportation vehicles. In any kind of wind tunnel - aerodynamic, climatic or acoustic - users are interested in optimization of the valuable factor time for the performance of experiments and measurements. Aerodynamic properties exerting direct influence to fuel consumption have to be optimized.
-
Product
PXIe Remote Control Interface Module
43-921-003
-
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling.
-
Product
Complete TAP Signal Isolation for Corelis Boundary-Scan Controllers
ScanTAP IsoPod
-
The Corelis ScanTAP IsoPod™ is an add-on accessory that provides a galvanic isolation barrier between the target system and the boundary-scan (JTAG) controller hardware. While the Corelis boundary-scan controllers are highly robust and reliable, the complete electrical isolation helps prevent damage to the controller from harsh electrical environments where over-voltage and over-current can damage components.This Corelis ScanTAP IsoPod was designed to add an additional layer of protection with minimal cost and effort. Open the box and plug it in; everything just works.
-
Product
PC Controlled High Voltage Testers
-
PC-controlled high voltage testers are instruments that use a computer to manage and control the testing of electrical components or systems at high voltages, often for insulation integrity or dielectric strength testing.
-
Product
Focus Control And Stabilization
-
Applied Scientific Instrumentation
The CRISP system is designed to maintain focus over time i.e. compensate for thermal & other factors that may cause the sample to drift out of focus over time. It also can be used to maintain a given focal point while scanning the sample in XY. If you are looking to find the optimal focal point while scanning through the sample in Z phase.
-
Product
Controllers & Software
-
Weiss Technik Controllers and Software offer advanced technology for Programming, Control and Monitoring for your testing.
-
Product
PXI Remote Control Interface Cable, 1m
41-924-100
-
The 41-924-100 is a 1m cable accessory for the PCIe to PXI Remote Control Interface Kit. The kit provides a seamless connection between a PC’s PCIe slot and a PXI chassis and is suitable for providing an interface to any PXI chassis.
-
Product
6 Slot PXIe Based Chassis with Embedded Controller
PXE6410
-
The PXE6410 is a PXIe based 6 based slot Gen 3 x4 chassis, that supports the Tabor Proteus Family of AWG’s and the TE330x family of PXIe RF amplifiers. The Chassis allows you to purchase any Proteus PXIe module and later add or up-grade to more channels, higher sample rates or higher output power.
-
Product
Safety Controllers
-
*Safe inputs and outputs*Layered safety concept, extended monitoring and test routines*Performance configurable in case of a fault*Quick boot-up and short fault detection time*High-performance CAN interface for various communication tasks
-
Product
Push Button Controller
Stack-Match II
-
Stack Match controller is a replacement for the rotary switch Stack Match controller. It features pushbutton switches for easy antenna selection and has outputs for both phase control and an auxiliary output. It is a component of the ShackLAN product line and as such can be fully remotely controlled via computer with our ShackLAN Control Center software. All outputs are switched with relay contacts for maximum reliability and power for the external switching unit may be applied from a separate power source to provide maximum isolation from the ShackLAN network. There is also a PTT input to allow different stack configurations for transmit and receive.
-
Product
RE Family SOTB™ Process-Based Energy Harvesting Embedded Controllers
RE0x
-
The first product based on SOTB™ process technology realizes intelligent and battery maintenance-free IoT devices
-
Product
Embedded Controllers & Expansion Modules
-
AMAX embedded controllers offer compact CODESYS automation solutions, paired with EtherCAT I/O for high-speed field connectivity.
-
Product
Safety Certified Controllers
HY-TTC 500 Family
-
The HY-TTC 500 family consists of high-end safety control units designed to satisfy upcoming needs for a wide range of high-end applications like construction and agricultural machines. The freely programmable high-end controllers with a powerful dual-core ARM Cortex®-R4 lockstep processor are protected by a compact, automotive-style housing suited for harsh environments. The safety controllers fulfill requirements up to SIL 2 (IEC 61508) / PL d (ISO 13849) / AgPLd (ISO 25119) – and can be programmed either in C or in CODESYS®. The safety certified CODESYS® Safety SIL 2 speeds up application validation of the certified controller significantly.
-
Product
Modular Multi-Channel Controller
LightMaster
-
Sciences et Techniques Industrielles de la Lumière
LightMaster is a modular multi-channel controller for chromatic confocal sensor heads.LightMaster has a total capacity of 48 simultaneous measurements with 12 Lighslot modules of four channels each.LightMaster is a 19"3U rack with a universal Ethernet GiGE interface compatible with a PC or PLC.
-
Product
Unprecedented Power Control
Ascent AP Series
-
Building on AE®’s premier bipolar pulsed-DC technology, Ascent® AP power supplies extend your ability to optimize output with advanced pulse shaping, as well as four-block progressive arc management that includes full voltage reversal and self-adjusting arc parameters. This compact solution’s patented pulsing technology proactively inhibits arcs, while its wide operational range unlocks material options to extend single- and dual-magnetron process flexibility and material innovation.
-
Product
Control Module for Combustible Apps
4802A
-
The 4802A is a single channel Combustible Gas Control Module that has been designed for use with General Monitors catalytic bead sensors. It is designed to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs.
-
Product
Ozonator Controller
SCI-552
-
Teledyne Advanced Pollution Instrumentation
The SCI-552 is a system controller for ozone delivery systems that provides electronic control interfaces for a number of typical system components, including: ozone generators, EV valves, mass flow controllers, back-pressure controllers, Teledyne API 452 ozone sensors, Teledyne API 470 dissolved ozone sensors, and a water chiller.
-
Product
sbRIO-9871, Non-Enclosed, 4-Port, RS485/RS422 C Series Serial Instrument Control Module
780879-01
-
The sbRIO‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The sbRIO‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. Non-enclosed modules are designed for OEM applications.
-
Product
Control Board For Testing PCBs
TCC 1800
-
The TCC1800 Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via a galvanically separated USB interface. The TCC1800 is designed to work with positive voltages up to 24V. All inputs and outputs are protected against higher voltages however. The card provides basic IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, Serial (UART) and I2C interfacing.
-
Product
Stepper Motor Controller for PCI
PCI322
-
The PCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications
