Battery Internal Resistance
-
Product
Hand‐held Digital Battery Tester w/ Thermo Printer, USB port
12-1015
-
• Tests 12V Flooded, AGM, Gel Cell, Enhanced Flooded (Start/Stop Batteries)• 10 Line LCD display• Performs ground test• Checks diode ripple• Stores last 250 test series with or without power• Carrying case, printing software and USB cables included• Built-in thermal printer with thermal paper (611305)
-
Product
NetXpert XG2 High Cap Battery Kit
#TXGBATX
-
*Easy installation*Increases battery capacity by 50%
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
Time Domain Induced Polarization /Resistivity Receiver
IPR-12
-
This allows you to troubleshoot and monitor data quality for the most efficient IP survey possible. With an IPR-12 you will have an excellent tool to get the best possible IP data from your survey.
-
Product
HEV Battery Reconditioner
-
Battery reconditioning and cell balancing is a well understood process for NiMH batteries. The procedure was initially developed for NiCad batteries decades ago. NuVant Systems has simplified the process to bring electrochemistry to the streets. The EVc unit is a push-one-button-after-wire-up system for small shops to large vehicle operators.
-
Product
Battery Load Tester
MD4260
-
Test capabilities: Battery voltage, battery cranking, battery charging volts and good/bad battery test. Test batteries on and off the car in just 30 seconds. Heavy duty copper-plated clamps. Internal loaded unit with a 100-amp load capacity. Load safety switch to prevent arcing. For 6- and 12-volt batteries.
-
Product
High Resistance Measurement Universal Adapter
N1414A
-
N1414A High Resistance Measurement Universal Adapter is used to simplify the connection for high resistance measurements by B2980A series electrometer.
-
Product
Car Battery Checker
BT-300
-
Konstar Electric Industrial Co., Ltd
Battery tester can test the car battery whether is ok, if the battery is bad or need charge or bad, the tester will give you the right check result, then can do the right plan for the battery before work.
-
Product
20J3 SHEET RESISTANCE METER
-
Non-contact measurement of Ohms/sq, Ohms-cm, resistivity, thickness, and moreMeasures nearly all thin conductive materials or coatingsChoose a sensor in one of four ranges, from .005 Ohms/sq to 100,000 Ohms/sqadd other sensors laterFor benchtop or inline applicationsSimple one-button operationSmall footprint with detached sensor probeOptions include vacuum-ready probe, PC-based productivity software, Ethernet connectivity, stage, and more
-
Product
Rechargeable Battery Telemetry Systems
2100R Series
-
Advanced Telemetrics International
Offers more performance and features while providing solutions to common shaft mounted obstacles. Separate but simultaneous data and status signals allow a variety of control functions independent of the high quality data stream ATi is known for. Battery power means lower noise floors, more versatile installations, no active power generation or tuning.
-
Product
Battery Testers
-
designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more.
-
Product
Resistance System - Digital Surface Resistance Meter up to 200 TeraOhms
PRS-801B
-
- Accurate Wide Range Resistance Measurements: 0.01 Ω to 2.00x1014 Ω- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Variable Voltage 0.1 mv to 9.99 V for low resistance measurements- Constant Test voltages 10V and 100V meeting ANSI/ESD S20.20- Auto Resistance Range Control- Auto Test Voltage Control- Uses a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- 999 Data Set Memory- Download to Excel® in Batches or Individual Measurements with Prostat Connect 2.0- Uses Micro USB Cable for Charging and Downloading Data- Charges in 2 Hours- 2-year Limited Warranty on Main Instrument
-
Product
High Accuracy Internal Measurement Ultima
-
• Ultima handles and kits with display unit D62S Advanced und absolute digital probe P12D• Measuring range from 2 to 310 mm• Resolution up to 0.0001 mm• Mechanical repeatability : 1μm from 2 to 60 mm, 1.5μm from 60 to 210 mm and 2μm from 210 to 310 mm• Robust construction designed for use by inspection and machine shop• UKAS certificate supplied with each head• UKAS certificate supplied with each setting ring.• Rings manufactured according to DIN 2250 part 2 (standard)• Blind bore measuring from 12 to 310 mm• Compatible with all Sylvac digital display• Special heads on request ( threads, grooves, splines, slot width, etc...)
-
Product
Contact Resistance Tester
JYL-200B/100B
-
Product description: JYL-200B/100B contact resistance tester can measure contact resistance of high voltage switches and circuit breakeres, also can test primar side resistance of transformer and grounding wire in groups
-
Product
Battery Cyclers
-
BioLogic’s battery cycler line-up is made up of two complementary ranges of instruments, the high throughput BCS-800 Series battery cyclers and the R&D grade MPG-200 Series test stations.
-
Product
Battery on-line Monitoring Tester
-
HD Power Test Equipment Co.ltd
Battery on-line monitoring system tester is a on-line battery monitoring and auto maintain system for USP,EPS, DC power supply, communication power supply . The tester has the function of monitoring and alerting for a series of parameters such as battery pack voltage, battery pack current, cell battery voltage, cell battery internal resistance, battery environment temperature, Cell Battery negative temperature and battery voltage balance, residual capacity and discharge. It can automatically maintain balance voltage, which used for on-line monitoring 2V and 12V battery.
-
Product
MINI Battery Discharger & Capacity Tester
IDCE-4815CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-4815CT can provide 0-150A (steps:1A) adjustable current for different test requests
-
Product
Battery Management LEM BMS Software
CELLooK
-
LEM is the latest and most advanced Battery Cell Monitoring System. The CELLLook is the web-based Software that could monitor, diagnose and analyze the Battery cell capability by an internet access. (Developed DB engine in Korea and registered a trade mark). The auto alarm, diagnostic and analyzing software for all Microguard data that Jaeshininfomation Co., Ltd with Web2.0 solution.
-
Product
Natural Cooling Input 380VAC 3 Phase to Output 190-300VDC 10A-40A Rectifier Battery Charger
SD230D20ZZ
-
Zhejiang Sandi Electric Co., Ltd
SANDI “SD” series intelligent high-frequency switch power supply modules are specially developed to meet the demands of modern DC system. The charger rectifiers are designed with world leading patent technology “resonant voltage type soft switching power supply technology”. They feature high efficiency and stability, intelligent control, small size and light weight. Standard RS-485 interface, easy to connect with automation system. “Four remotes” functions, intelligent management. The products are widely used in power plant, substations and etc..
-
Product
200V 20 Ohm Portable Battery Resistance Voltage Tester
TOB-SM8124
-
Xiamen Tob New Energy Technology Co., Ltd
200V 20 Ohm Portable Battery Tester For Battery Voltage and Resistance Testing. TOB-SM8124 Resistance Voltage Tester is a portable battery tester used for battery voltage and internal resistance test, it is Suitable for lithium-ion battery, nickel-metal hydride, lithium manganese, lead-acid battery and other single battery or battery pack with voltage no more than 200V.
-
Product
Testing Solution & Battery Emulation
PLUTON
-
The PLUTON solution is a programmable DC power supply designed to function as a source or a regenerative charge.
-
Product
Resister Blackjack
-
Resistor blackjack is like regular blackjack but better! Your goal is to assemble a single resistance from several resistors that is as close to 21k while not being over.Unlike regular blackjack, the resistors can be combined in series and in parallel, giving the game a whole new dimension. Plus, resistors have tolerances so achieving a mathematical 21k doesn't guarantee a win.
-
-
Product
Battery Cycle Test Systems
-
Chroma Systems Solutions, Inc.
High precision, integrated battery charge / discharge cycle test systems designed for lithium ion and other chemistries and applications including EV batteries and energy storage systems. Chroma’s battery test equipment provides advanced features including regenerative discharge systems that recycles energy from the battery back into the channels in the system or to the grid. Systems are configurable and flexible with multiple channel capabilities that can be upgraded as testing requirements change.
-
Product
12V 0-500 Amp Carbon Pile Battery Load Tester and 12/24V Electrical Systems Tester
6042
-
• Test batteries up to 1000 CCA• Interprets data from the charging/starting system on easy-to-read LCD displays• Shows positive and negative amps for easy diagnosis of current leakage problems• 0-500 Amp variable carbon pile load tester• Unique curved carbon discs ensure maximum contact, fewer hot spots, smoother operation and longer life• Heavy-duty single extruded leads for testing up to 15 feet apart• Test electrical systems on 12/24 Volt systems• Test all battery types• Ideal for testing remotely mounted batteries accurately• INCLUDES: Model 6043 1000 Amp AC/DC Inductive Amp Clamp for checking starter draw or parasitic drain test, also can be used with conventional multi-meters; heavy duty, two wheel tilt-back cart with 8” wheels and 2 trays.• Made in USA of US and Global Components
-
Product
Battery Module/Battery Pack Test
-
The battery test system CT3001B and CT3001D provide solutions for battery module/battery pack test with higher current/voltage. They can also be used in situations that batteries are charged/discharged at high rates. Different current/voltage range and channels numbers can be custom made based on the requirement.
-
Product
Non-contact Inline Sheet Resistance Measurement Module For Conductive Layer On Substrate
NC-700
-
*Inline measurement module for moving substrates such as PET film, glass or paper*Continuous measurement(~24h) in Roll to Roll with OFF-SET FREE capability system*Various applications from the research and development to the production line
-
Product
Resist Processing Systems
-
The EVG100 series resist processing systems establish new standards in quality and flexibility for photoresist coating and developing. Designed to provide the widest range of process variations, the EVG100 series’ modularity offers spin and spray coating, developing, bake and chill modules to suit individual production requirements. These systems accommodate the processing of an extensive range of materials such as positive and negative resists, polyimides, double-sided coating of thin resist layers, high viscosity resists, and edge protection coatings. These systems can handle more than one substrate size, from 2" to 300 mm diameter, rectangle, square or even irregular shaped substrates, with no or very short tooling time. This allows the development of new devices or processes on an industrial level, which not only requires high flexibility but also controlled and repeatable processing. EVG has built up many years of spin and spray coating experience for demanding applications and incorporates this knowledge into the EVG100 series, where our process know-how can be leveraged to support our customers.
-
Product
Water Resistant, Stand Alone, Humidity and Temperature Data Logger
RHTemp1000IS
-
The new RHTemp1000IS Intrinsically Safe humidity and temperature logger is a rugged, battery powered, stand alone device which can be used to automatically record humidity and temperature. This compact, portable, easy to use device is able to measure and record up to 16,350 humidity and temperature measurements per channel.
-
Product
DC Resistance Tester
ZLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.2-2008Used to measure conductor with nominal diameter ≥0.01～9.0mm or various round or flat copper and aluminum wires and other metal wires with DC current resistance of 100μΩ～99.99Ω;Combination of intelligent DC conductor resistance measuring meter and DC resistance test fixture with sample straightening function;Test range can be selected according to the resistance value of sample, and after clamping samples current resistance value would be displayed;Both potential fixture and current fixture are made of copper;The application of microcomputer control allows for full-automatic completion of test;LED will intuitively display measurement results;
