Battery Internal Resistance Testers
See Also: Resistance Test, Battery Conductance Testers
-
Product
Socket Testers
-
Socket Testers including 4 Pole RV Output Socket Tester, Blade Socket Tester, 7 Pole Plug Output Tester, 7 Pole Socket Output Tester.
-
Product
Lithium-Ion Battery Pack, B2983 / B2987
N1418A
-
Use for the B2983A femto/picoammeter and the B2987A electrometer/high resistance meter.
-
-
Product
Medical Grounding Resistance Tester
2678YM
-
Shenzhen Chuangxin Instruments Co., Ltd.
Medical Grounding Resistance Tester，Product Introduction2678YM Medical Grounding Resistance Tester Is Used To Measure The Internal Electrical Equipment Of Grounding Resistance,Which Reflects The (Contact) Resistance Of Total Grounding Terminal Of Electrical Equipment.It Suitable For Measuring All Kinds Of Motors,Electrical Appliances,Instruments,Household Appliances And Other Equipment Resistan
-
Product
Cable Tester
CableJoG 128
-
The CableJoG 128 can test up to 128 individual connections of all manufacturers of connectors. This simple test instrument stores up to 55 separate connection configurations. Each cable that is tested is compared with the configuration stored in its memory to produce a pass/fail indication of each pin connection.
-
Product
In-Line X-ray Inspection System for Secondary battery
X-eye 9000 Series
-
X-ray Tube100 kV / 200 µAMin. Resolution5 µmInspection Ability120ppm , 150ppm, 180ppmSystemConveyor / Index / Pick&Place 방식 LoadingDimension1,800(W) x 1,560(D) x 2,070(H)mm / 5,000kg
-
Product
Intelligent Battery Charger-Analyzer for Battery Systems
SuperMini
-
The SuperMini is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMini can satisfy the requirements of most ( Up to 40 A-hr ) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Electrical Testers
-
CURT electrical testers are perfect for testing a new wiring harness on your vehicle or troubleshooting the existing wiring. Our trailer plug testers are built with LEDs and are available in 4-way, 5-way, 6-way and 7-way. We also offer brake control testers.
-
Product
Battery Tester Battery Test Machine
2523
-
Shenzhen Chuangxin Instruments Co., Ltd.
With Chuangxin’s experience in impedance test and marketing survey, the new battery tester-TH2523 is successfully launched. It can be competitive with other similar products with its outstanding performance, easy operation and new look.
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Standard Series
-
When it comes to winding resistance measurement on three-phase power transformers and autotransformers, TWA Standard series offers some of the most technically advanced instruments with LCD display in the market. Both models are capable of testing six transformer windings with a one-time cable connection, as well as three-phase automatic transformer demagnetization. The stored magnetic energy is safely automatically discharged at the end of the test. The built-in tap changer control unit enables automated test mode, where the instrument operates the tap changer without operator input and records winding resistance results based on pre-selected stabilization criteria. This option makes the operator’s job significantly easier.Both models can output test currents from 5 mA to 25 A DC for the purpose of winding resistance measurement. TWA40D has a special test mode for checking the synchronization of on-load tap changers with three phases simultaneously tested in parallel, in which the total test current can rise to up to 40 A DC.TWA40D has additional advantages when it comes to non-intrusive tap changer analysis. The unique DVtest method enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, simultaneously with the measurement of tap changer motor current which helps with the detection of motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or on three phases simultaneously. It can also be performed as an additional test simultaneously with the winding resistance test in all tap positions.An additional unique advantage of TWA40D is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer (connected in a YN configuration). This can significantly shorten the total testing time – for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.The test leads for TWA three-phase transformer winding ohmmeters are interchangeable with the TRT turns ratio testers, which means that both sets of tests can be performed with a single test lead connection to the power transformer terminals.
-
Product
Static Tester
-
Electrostate tester with LED indicator for the detection of static charge in the plus and minus range. An indispensable, inexpensive tool for the assessment and selection of materials in the living area, as well as the quality of the room climate.Buy Data Sheet
-
Product
Lead-acid Storage Battery Analyzer
-
From the beginning of 2006 the verification of measurements of the analyzer of lead-acid chemical sources developed by Company "Megaron" is spent in Test laboratory "Neva-Reglament". The analyzer is intended for the express-estimation of a condition of lead-acid batteries: before the first use of new battery (an estimation of the electric characteristics declared by the manufacturer); during the battery operation (an estimation of a condition and working capacity at real application).
-
Product
Resistance Measurement Meters
-
Shanghai Beha Electronics Co., Ltd.
The meter digital milli-ohmmeter is a battery operated instrument wich supply a low current to the circuit under test, with which, stable, accurate measurement of low resistance can be made, still, over a wide range of values.
-
Product
Light Testers
-
Hall’s have designed and manufactured products for oil, industrial, farming, commercial, and transportation markets. Products such as truck and trailer light testers, bop savers, early engine warning systems, oil spinners, engine control panels, dashes for service rigs, drillers panels, and sandline controls. Halls have been involved with over the rebuilding from scratch of over twenty service rigs.
-
Product
Cable Testers
-
Ningbo Betterbell Telecommunication Equipment Co, Ltd.
Suitable for testing the connection and seriation of 10-base-T(VTP/8TP)-AT 8C T258A.TIA568A/B. Token Rine and Vsoc4/6/8. This tester can be used conveniently, and can find connection fault easily and quickly.
-
Product
SMD Testers
-
Is a miniaturized and integrated utility model measuring instrument, which can automatically identify components such as resistance, capacitance, diode, etc., with LED, voltage regulator, DCV, on-off and battery power measurement functions. SMD resistance, capacitance, diode (RCD) parameter measurement, is a good helper for electronics factories and electronics maintenance.
-
Product
Battery Test & Management
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of products for testing and measurement of battery from your critical power systems. It includes battery online monitoring system, battery tester for internal resistance/conductance, battery charger, battery load bank, battery data logger, battery charger/discharger and so on.
-
Product
Resistivity Meter
Model 2180
-
The unit is compact and lightweight. The basic system is 7″ wide by 2.5″ high and 12″ long. When measurements are needed below approximately 100 micro-ohm-centimeters, the basic system is piggybacked onto a second enclosure that houses a power amplifier with a current gain of ten. The combined unit measures 7″ wide by 5″ high and 12″ long. The combined unit weighs 11.5 pounds. Two short cables interconnect the two enclosures for powering the power amplifier and routing the signals to the fixture or four point probe. The front panel of the basic system includes a 32-character backlit LCD display and a set of function keys. An easy-to-use menu will allow access to user defined parameters such as sample thickness, sample volume, and calibration constants; upper and lower alarm limits, relative measurements, and several others.
-
Product
Insulation Testers
-
Preventive maintenance is always a must, especially in motor instrumentation. Knowing before a problem arises, allows time for scheduled shut downs, instead of shutting your process down when you need it the most. Yokogawa offers many varieties of Insulation testers, from our “Hand Crank” version to our Analog and Digital 1000V versions.
-
Product
Open/Leak Tester
-
NIDEC-READ testers undertake various types of continuity tests at broad voltage and resistance levels.
-
Product
ESD Tester
PurePulse
-
PurePulse is a flexible and efficient ESD tester for HBM, TLP, MM and HMM. Its 2-pin style setup reduces tester parasitics, it captures waveform data and can be automated to test thousands of pins without the need for a test fixture. Our PurePulse system was designed from the ground up to be customized to meet your testing needs, take a look at the features below and schedule a demo with us to learn more.
-
Product
Torque Tester
WDIS series
-
Management of various torque tools PLC and connection alsoWDIS-IP (05/5/50/200/500/1500), WDIS-RL (005/05/6/10), WDIS-IPS (05C/5C/20CL). The DIS series has become easier to use and has higher performance. Interlocking with a personal computer or PLC, the torque measurement can be managed at a higher level.Management of manual torque drivers and wrenches, management of automatic and semi-automatic tools, inspection of screw tightening and loosening torques
-
Product
Battery Charger
-
Rishabh Instruments Pvt. Ltd.,
1Phase,Universal Input Range 90-280 VAC, 127-396 VDC, High efficiency ≥86% & extremely compact (w-h-d) 55X110X105mm & DIN Rail Mountable with protections
-
Product
CDM Tester
-
Tokyo Electronics Trading Co., Ltd.
Determine what level of CDM discharge causes device damage by placing the device package on a metal plate with the pins facing up.
-
Product
LCRZ Tester
DU-6218
-
Delta United Instrument Co., Ltd.
Wide Measuring Range & High accuracy 0.1%Zeroing Offset FunctionProvided HI/LOW limit and BIN Sorting comparator function, to meet your needed.100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceEasy Test Condition Setting with Auto Parameter Selection & Auto Ranging Function High speed FADC, max. test speed up to 55 meas./sec, faster your automation equipment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
Product
Ferroelectric Tester
Premier II
-
The Precision Premier II, is one of Radiant's most advanced test systems. The Premier II has the large envelope in terms of frequency response, voltage range, and accuracy of any ferroelectric tester in the world. Vision Software is provided with the Premier II Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choice from.
-
Product
Internally Ruggedized Phase Stable Test & Measurement Test Lead Assemblies
Storm-Test®
-
- Engineered to provide precise measurements with stable electrical performance- Excellent loss, VSWR, & phase/amplitude stability with flexure. - Internally ruggedized cable construction delivers longer life, repetitive mating and prevents crushing, bending & twisting- Accurate & repeatable measurements - Performance tested prior to shipment
-
Product
Insulation Resistance Measurement
MD 5KVr
-
The digital insulation tester model MD5KVR is TENTECH's cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 5 TΩ, with 4 preselected test voltages, 500 V -1 kV - 2,5 kV - 5 kV. Other test voltages, from 50 V to 5 kV, can be selected in 25 V or 500 V steps.
-
Product
HiPot Tester
HiPot-30
-
The SURETECH HiPot 30 tester provides an economical solution to Low frequency AC and DC testing of cables,terminations, motors, generators and other electrical apparatus. 0 – 30kV
-
Product
Compact Tester
-
Designed for testing a family of products with similar functionality. A cost-effective solution for simple PCB architecture. Measurement system integrated with the adapter. Allows the use of interchangeable adapter inserts, including tandem type. Allows you to expand the scope of functionality. Optional interchangeable adapters (fixtures). Perfect for low-volume production
