Breaker Test Systems
-
Product
Compact EMC Test System
Multi-CE5
-
The Multi-CE5 includes an Electrical Fast Transient Generator (EFTG), a Combination Wave Generator (CWG) and a Coupling-/Decoupling Network (CDN) for single-phase power supply lines. The software program CE-REMOTE allows full remote control of the test generator via Ethernet light guide as well as recording, evaluation and documentation of test results, according to IEC 17025. To record the wave shape of impulses, it is equipped with an Impulse Recording Function (IRF).
-
Product
Three-phase Fully Automatic Test System
TS41
-
Calmet Smart Calibration Devices
The Calmet TS41 test system consists of a three-phase reference meter of accuracy class 0.02% (or 0.04%) and an integrated three-phase current and voltage source up to 3x120A/600V. It makes possible automatic testing of electricity meters in meter test stations
-
Product
Backplane Test System
402HV
-
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Product
Mezzanine System
3560
System
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
Product
Pneumatic Horizontal Shock Test System
KRD12 series
-
The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
Product
Automated Test Systems
-
Chroma Systems Solutions, Inc.
From power conversion to battery to electrical safety, our test systems will maximize your time, improve your validation process, and increase your throughput.
-
Product
Intraocular Lens Optical Test System
OptiSpheric® IOL R&D
-
The OptiSpheric® IOL R&D is specially designed for the analysis of single intraocular lenses in research and development. With the OptiSpheric® IOL R&D, important parameters of all types of lenses (monofocal, multifocal, trifocal, toric, aspheric and those with extended depth of focus (EDOF) – whether diffractive, refractive or sectors) can be measured and tested in air or in situ in accordance with ISO 11979.
-
Product
Meter Test System
MTS-100
-
Kongter Test & Measurement Co., Limited
This Meter Test System features state-of-art designing with high accuracy. It is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 120A). This system is particularly designed with modular structure for calibration and test of different single phase/3 phase electronic/inductive active and reactive energy meters.
-
Product
Test System for Circuit Breakers
-
Spitzenberger & Spies GmbH & Co. KG
Thermal testing with long-time currents up to 550 A. Magnetic testing with short-time currents up to 2000 A. Control software. Customer specifically adapted. 4 candidate records with pneumatic adapting.
-
Product
Ultra-sonic Test System
V-Meter
-
The V-Meter is an advanced ultrasonic, pulse-velocity test system widely used for quality control and evaluation of concrete structures. It can identify non-homogeneous conditions such as voids, cracks, honeycombs and frozen concrete.
-
Product
Meter Testing System
ASTel
-
Three-phase Meter Test Equipment of ASTeL 3.2x.x series system is a fully automatic system enabling simultaneous, multi-position calibration and legalization of electric energy meters. The automatics include power sources, reference standards, stand controllers, photoelectric scanning heads, separating transformers, and other elements of the system. All these elements are controlled through a Windows based executive program.
-
Product
(250 kN) Fatigue Testing System
8802
-
The Instron 8802 is a high stiffness, 250kN fatigue rated servohydraulic testing system that meets the challenging demands of both static and dynamic testing requirments. The 8802 systems include a range of configurations available to provide complete testing solutions to satisfy the needs of advanced materials and component testing. The design of the 8802 frame makes it ideal for installation within a laboratory environment, generally without the need for strangethened floors or raised ceiling heights.
-
Product
Multi-Purpose RF Test System
SPA441
-
The S - Series multi-purpose RF test system can be used in many applications such as R&D lab, ATE factory testing, EMC testing, field testing, and general purpose RF design. The S - Series is a flexible alternative to expensive and bulky RF test equipment. As shown in the setup in the upper right the S-Series system can be utilized to simultaneously provide all RF functions using its 7 inch front panel display or can be connected to a larger monitor for ease of viewing multiple windows at the same time
-
Product
Gel Strength Test System
LD-LGST-A10
-
Gel Strength Test SystemLD-LGST-A10is mainly used to measure the gel strength of gelatine under the stipulated environment. It has traveling accuracy ± 0.3 % and Test range up to 5 to 1000 g Bloom. It consists of Jelly Strength Tester, Constant Temperature Bath and Refrigerator. Sampling depth can be present arbitrarily in 1 to 60 mm. It consists four kinds of sampling measurement modes: single-step, maintaining, circulating and automatic.
-
Product
Dynamic Test System
3430-SW
-
The Dynamic Test System 3430-SW measures dynamic characteristics of IGBT/MOSFET devices at high speed. Maximum of 4 parallel measurement is available by connecting the 3430-SW mainframe test stations for each test items ( normal 2stations). One PC controls the whole system.
-
Product
Test Automation System
RT-Tester
-
Verified Systems International GMBH
Designed to perform automated hardware-in-the-loop tests and software component test on process or thread level for embedded real-time systems. The functional components of RT-Tester can be structured as shown in the figure to the left. Please click on the small image to enlarge the picture. The System Under Test (SUT) denotes the object to be tested.
-
Product
Test Program Execution for High-Volume Production Systems
ScanExpress Runner Gang
-
Electronic manufacturing test systems must be fast and efficient. Schedules today are shorter, products are more complex, and the market demands higher speed—the product needs to be built and shipped yesterday.ScanExpress Runner Gang Edition is a concurrent boundary-scan and in-system programming test executive designed specifically for high volume production. Unlike traditional test systems which execute sequentially on a single unit under test (UUT) at a time, ScanExpress Runner Gang Edition provides concurrent (gang) testing on up to 8 UUTs for improved test and programming times.
-
Product
Keypad Test system
Mistral
-
Engineering Solutions Inc. (ESi)
The Mistral Keypad Test System has been designed to be the least expensive, easiest to use full featured tester for membrane switch assemblies. The idea is to combine a small, smart "pod" with a PC running software that makes full use of the Windows® graphical interface. Make it as easy to set up and use as possible yet include all the features you need.
-
Product
Tracker for Testing CPV Module Systems
-
The tracking precision of our biaxial tracker is better than ±1° on each axis, with an option for ±0.1° precision. This makes the tracker ideal for testing concentrating PV modules. The software runs all required tests for angle-dependent testing of PV modules according to IEC 62108.
-
Product
Communications Test System for Frontline Diagnostics
ATS3000P
Test System
The ATS3000P is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000P also includes the sophisticated IF and baseband I/Q DigitalSignal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easyto-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets are available for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
Hydraulic Pulse Fatigue Testing System
PFT-500
-
Jinan Testing Equipment IE Corporation
PFT-500 hydraulic pulse fatigue testing machine is mainly applicableto large size parts such as bridges, trusses, automotive chassis, front and rear axels, locomotive frames, chassis and various concrete structures for static compression test and dynamic unidirectional pulse fatigue tests. The Fatigue Testing System for Rail has significant characteristics of reliable design, simple operation, energy conservation, and low operation cost etc.
-
Product
Automatic Tablet Testing System
UTS 4.3
-
The UTS 4.3 LAB is a universal and fully automatic tablet testing system based on the long-proven UTS 4.1 - this was developed for industrial use and can be found in production worldwide. The UTS 4.3 LAB is now equipped with the database-driven, intuitive all-in-one touch software and no longer requires additional software solutions for most areas of application.The functionality of the software can be extended modularly and individually adapted to your needs and requirements. FDA regulations can be fulfilled with the optional FDA-21-CFR-Part-11 module.With UTS 4.3 LAB – as with the proven UTS 4.1 IPC – you can test round, oval, square and rectangular tablets as well as numerous special shapes. For difficult oblong tablets, the globally used Oblong Centering System (OZB) can also be integrated.
-
Product
Double Lift Zero-distance Drop Test System
KRD42 series
-
KRD42 series double lift zero drop tester is mainly suitable for large size packaging products to resist drop impact performance, its powerful power system and unique sample support for easy loading and unloading of oversized, overweight items, and automatically rise to the set height, complete the drop test.
-
Product
Modular Breakout System 8-Pin Power D-type Plugin Module
95-191-002
Modular Breakout System
The 95-191-002 Plugin Breakout Module is designed to be fitted to a PXI 40-191 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
Test Cell Vibration Monitoring System
-
The Test Cell Vibration Monitoring System is a complete package for monitoring dyno vibration levels generated during engine testing. This system was design to prevent catastrophic dyno failures.
-
Product
Handheld Test Systems
-
Lightweight and easy to use handheld test systems designed with a plug and play approach, ideal when operating on site or close quarters.
-
Product
Universal Testing Systems (Up To 300 KN)
3400 Series
-
Instron’s 3400 Series universal testing machines offer dependable performance across a broad spectrum of mechanical testing applications, with force capacities ranging up to 300 kN. These systems are well-suited for basic tensile, compression, flexural, peel, puncture, friction, and shear testing, and can be easily configured using a wide selection of grips and fixtures from Instron’s accessory catalog. Built with user safety and efficiency in mind, each system incorporates Instron’s proprietary Operator Protect technology, ensuring a secure and intuitive testing environment.
-
Product
Stator Testing System for EV Motor
EVT531
-
Shanghai Dean Electrical Co., Ltd
To meet the standard test projects requirement of the international companiesTo control and analysis the programs will reduce the human careless and misjudgmentEasy to edit environment and easy to learnIt can test multiple sets of DUTs simultaneouslyWhen there are several DUTs are tested, it could identify the undesirable sets individuallyThe Impulse/Surge with waveform comparison is a non-destructive analysisPolarity testMaximum saved files will be up to 100 setsIt provides the password functionSpeeding test could save time and improve efficiencyChinese and English pages can be arbitrarily switched
-
Product
Rotary Table Test system
-
The requirement was to develop a test system that can take very different test and programming times into account so that the hardware used can be used in the best possible way.
-
Product
ARTES Automatic Relay Test Systems
-
The purpose of power system protection is to use accurate and reliable protection devices to detect faults promptly and without fail and to minimize impairments to the power supply by selectively switching off faulted sections of the system.The use of suitable protection devices can significantly improve the safety and reliability of complex electrical power systems and installations. Regular testing is the only way to ensure that these protection devices function correctly throughout their operational life.More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the third generation of ARTES test instruments. Back in 1996, KoCoS was the first company to present Windowsbased testing software for controlling and operating test equipment and the company continues to play a pioneering role in the design of clearly structured and ergonomic user interfaces today.
