Breaker Test Systems
-
Product
Test System
USB Explorer 280
-
The Ellisys USB Explorer 280 is a sophisticated protocol test and analysis system for USB SuperSpeed traffic monitoring, driver and software stack debugging, and performance analysis.
-
Product
Electrolytic Capacitor Test & Scanning System
DU-9001
-
Delta United Instrument Co., Ltd.
The 10 capacitor - LCC/DZ/R in order to automatically scan test improve the test reliability and test efficiencyEach test channel can be opened / short circuit return to zero with high precision.Wide range scan box can be used to test 3mm~35mm 10 capacitorsSuitable for high voltage capacitance test, 450V330uF 10 capacitors can be smooth test
-
Product
MMIs for Test and System Integration
-
Laying out a custom PCB is too time consuming and costly for most rush projects. Pulse Research Lab has developed Mini Modular Instruments ™ to provide cost effective solutions to the most common engineering challenges.
-
Product
High Current Discharge Testing System
DTV
-
Cold Crank Testing to industry standards: IEC, SAE, BCIDischarge capacity performance testing to thousands of amperes
-
Product
SRS-200A Spectral Radiation Safety Test System
-
Hangzhou Everfine Photo-E-Info Co., LTD
SRS-200A is a new generation of portable photo-biological safety test and evaluation equipment. Based on the mainfunctions of the laboratory spectral radiation safety test system, the convenience and operability of test are fully considered.To some extent, the analyzer makes up for on site measurement insufficiency.
-
Product
12/24 CH Insertion Loss/Return Loss Automatic Testing System
CA3201
-
UC INSTRUMENTS CA3201 12/24 CH INSERTION LOSS/RETURN LOSS AUTOMATIC TESTING SYSTEM is special designed for MPO/MTP fiber cable and multi-channel fiber optical devices like PLC device. It also can be easy changed into AWG DWDM devices testing system ifwe change 1310 /1550 nm light source into UC INSTRUMENTS’ tunable laser source.
-
Product
Microindentation Hardness Testing Systems
LM Series
-
Perfect for a production facility or a research lab, LECO's LM Series Microindentation Hardness Testing Systems offer a variety of models (including analog and digital) with the advanced features that meet your requirements and budget.
-
Product
(2500kN+) Fatigue Testing Systems
8806
-
The precision mechanical systems, combined with the advanced features of the 8800 digital controller and Dynacell™ load cells, enable Instron to supply fully-integrated turnkey solutions to meet the most demanding applications. The system can be used to cover a broad range of static and dynamic test applications, covering metals, rebar, high-force fracture mechanics, aerospace panels, civil engineering components, wire ropes, or concrete.
-
Product
Transforming Analog Circuit Breaker Testers
MAC-21
-
The MAC-21 uses proven microprocessor and A/D converter technology to provide real-time waveform analysis. This ensures accurate true-RMS readings of current pulses, even with DC offset and distortion, which are typical in primary injection testing. Intelligent threshold algorithms provide accurate trip time measurement. Integration of measurement and control functions allow advanced features such as preset on times, auto ranging, and optional printer or computer interface.
-
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
Test Fixture
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Automotive EMC test systems
-
Dozens of manufacturer's and other automotive immunity standards with their roots in ISO 7637 continue to evolve bringing new challenges to users of conducted immunity testing. Teseq continues to advance the state of the art, bringing simple, flexible solutions for the challenging and fast-changing requirements that are 42 V ready.Teseq has been at the forefront of the pioneering work to establish EMC tests for motor vehicle electronics. Automotive manufacturers and suppliers worldwide have come to trust test systems from Teseq. Active involvement in the standardization committees ensures that the latest advances are continously reflected in our test systems.
-
Product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
-
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
Product
General Purpose Functional Test Systems
-
Keysight Technologies’ TS-5000 Family of Electronics Functional Test Systems offers a wealth of choices in general purpose instruments, power supplies, switch loading and DIO capabilities in a multiple rack heights, seamlessly connected with open architecture software Test Exec SL, all immaculately assembled and thoroughly tested so you don’t have to.
-
Product
Electroluminescence Test Systems
-
The products of the SolarModule EL-inline family are integrated into a module production line, before lamination, after lamination or at the end directly after the performance measurement. High-resolution cameras provide excellent image quality and allow the automatic detection of relevant defects. A manual evaluation of images is no longer necessary, which means that considerable costs can be saved. Communication to upstream and downstream processes is flexible and can be adapted to all common interfaces.
-
Product
High Voltage DC Cable Test Systems
-
We can offer from ±18kVdc to ±30kVdc units which all have automatic earthing for discharging capacitive loads. They are designed to perform tests on installed cables and jointing systems.
-
Product
Combined Environmental Reliability Test System
VTC SERIES
-
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
Product
Small Drop Test System
KRD41 series
-
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
Product
Software for Testing Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
We offer extensive and powerful software packages for our systems. All of our testing systems are controlled with our Hillgus testing software and the test results are stored in our open file formats. With our evaluation software Oculus, the findings can be subsequently evaluated and documented. Both Hillgus and Oculus were developed in-house and are constantly being improved. Due to the modular structure, the software can be optimized for every requirement and expanded at any time.
-
Product
Fiber Optic Test System
OPTOWERE-S100 (Fiber Optic Test System)
-
The frame of FOTS system consists of the Main control part and the Slot mounting part. The Main control part is in charge of control and interface of the system and the Slot mounting part can hold up to maximum 8 slots, which are modularized according to each function and come out in five kinds. This integrated test system is designed to help manage the test and measurement related to optical communication and component. And the modular architecture of FOTS allows for customized configuration so that the slot of LD Driver, 2 channel VOA, 1 X 4 switch, WDM EDFA and C + L – Band ASE Source can be chosen according to user’s necessities. Main control part and each function module are run by effective and multi-functioned system control program in the base of high speed remote interface, GUI display and the discriminative high speed driving of module and system. This system can provide variety manufacturing and laboratory applications such as general quality test and reliability test of optical component and optical signal transmission test through efficient linkage with other system.
-
Product
Test Systems
-
6TL’s speciality is simplifying the architecture of test systems, so that our customer’s Total Cost Of Ownership is drastically minimized. The technology that conveys our mission is called FastATE.FastATE technology is based on using intelligent modules to build test systems.
-
Product
Digital Circuit Breaker Analyzer
CT-8000 S3
-
The CT-8000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-8000 S3 is available with 3 (part number 9103-UC) or 6 contact timing channels (part number 9104-UC). The CT-8000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Also, an outstanding feature of the CT-8000 S3 is the ability to perform dynamic resistance tests on circuit breaker contacts.
-
Product
Test Adapters / Aeroflex Test System
52xx / 5300
-
We develop and manufacture test adapters for your existing interface including documentation and test program
-
Product
Test Cell System
qCf FC50/125
-
qCf: Our revolutionary test cell system for the professional characterization of fuel cells.
-
Product
ATE Test Systems
-
Introducing the Procyon ATE System! When it comes to ATE Test Systems for a for low- to high-volume production, Intepro has the testing power you require to be successful. For more than three decades, Intepro Systems has designed, built and integrated power supply test equipment for the world’s largest and smallest power supply manufacturers.
-
Product
Vibration Testing System
F Series
-
Suited to durability tests for all industrial products such as aeronautical, automobile, electronic and precision equipment.
-
Product
Vision Systems
-
Starrett Video-based measurement systems combine high-resolution images, powerful intuitive software and precision mechanical platforms to deliver superb accuracy and repeatable measurement results for a wide range of precision measurement applications.
-
Product
VLF test system
BAUR PHG 80 portable
-
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
Product
SIP-90-5 Test System Interface Probe
SIP-90-5
ICT/FCT Probe
Overall Length (mil): 1,000Overall Length (mm): 25.40Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
Communications System Analyzer
Freedom R8200
System
The Freedom R8200 from Astronics Test Systems represents a major step in the evolution of the Land Mobile Radio Test. The Freedom R8200 is the first and only test instrument that combines comprehensive digital and analog LMR testing with the ability to measure important RF network characteristics, such as Distance to Fault (DTF), Return Loss, and Voltage Standing Wave Ratio (VSWR). The Freedom R8200 is also the only service monitor with the abilityto display advanced RF Parameters in a Smith Chart for more complicated network analysis
