-
Product
Field Testing
-
Electronic force measuring device with digital display in MN / m², switchable for load plate.
-
Product
1 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1000
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1000 is ideal for 200–600 MHz oscilloscopes.
-
Product
Power ICs - Smart Load Switches
-
Combining multiple functions in a single IC, Vishay smart load switches eliminate the need for external circuitry . A simplified GPIO interface allows for power distribution and sequencing of multiple sub-systems. Slew-rate-control devices provide a controlled supply ramp to reduce inrush current, while fault protection and isolation switches increase robustness with reverse current, overtemperature, current limiting, and short circuit protection features. The ICs offer quick output discharge and small footprints, while their integrated design saves PCB space compared to discrete solutions, reduces BOM counts, and lowers manufacturing costs.
-
Product
Emissions Dynamometers
MD-AWD-1000-M
-
The MD-1000 sets the industry standard for heavy duty chassis dynamometers due to its rugged design and accurate loading capabilities. The AWD upgrade expands your testing to include full time 4×4/AWD applications! Now your testing capabilities have expanded! Simulate on-highway driving conditions under real world loads. Adjust loading to simulate a host of in-use operating conditions. The AWD 1000 is approved for use in Nevada and Colorado for Diesel Smog Testing.
-
Product
3-slot Network Attached File Server
DTS3
-
Curtiss-Wright Defense Solutions
The Data Transport System 3-slot (DTS3) is a rugged Network Attached Storage (NAS) file server for use in mobile vehicles, field ground stations, and aircraft. The DTS3 is easily integrated into network centric systems providing an easy-to-use, turn-key, rugged Network File Server (NFS). The system houses three Removable Memory Cartridges (RMC) that provide quick off load of data.
-
Product
Universal Clamp Tester
M-310
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The unique U type CT enabled to measure the load current of single or three phase cable without separating the cable to the wires. Leakage current measurements with least affection from the external magnetic field. Wide current measurements.(AC0.01mA-300A)
-
Product
Serial Production Mark Quality Control
-
The control system is based on the Sick IVC smart camera, which not only captures, but also processes the image. After training on the font samples, the system practically does not require the operator's attention in addition to setting the current marking for control. The character set can be specified by the operator or transmitted via the interface from the printer or from the enterprise information system.The camera software works autonomously: it loads all settings from the camera's permanent memory, initializes the backlight electronics and waits for a signal from the object presence sensor. When a signal is received from the sensor (an object in the shooting area), the camera captures the frame, searches for markings and analyzes the symbols for their compliance with the exemplary set.
-
Product
PXI 10 x DPST 8 Amp Power Relay Module
40-160-002
-
The 40-160 module has a choice of 10 x SPST, 20 x SPST or 10 x DPST Power Relays, suitable for switching inductive/capacitive loads up to 10A at 250Vac.Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.It is suitable for applications requiring switching of either mains voltage or DC current.
-
Product
Strain Gauge Test
-
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
Product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix topology With Column Protection Resistors
782385-12
-
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
DCDC
HA/HP Series
-
The HA/HP series features the latest in MOSFET design, state of the art surface mount technology, and offers a 4:1 ultra-wide input range, and efficiencies greater than 75% (typ). Features include Pi input filter to reduce input reflected ripple, continuous short circuit protection, and excellent line and load regulation of ±0.25% for line and ±1.0% load. Additional standard features include, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. All models are packaged in a six-sided shielded miniature case measuring only 2.0” x 2.0” x 0.375” high.
-
Product
Qualification Testing
-
Qualification, functional, and operational testing are important steps in evaluating how well spacecraft, launch vehicles, and other mechanical/electrical systems perform under severe loading conditions that occur during launch and operation.
-
Product
Universal Manipulators
-
optimized distribution of force allowing smooth and easy operationsminimized footprint/floor space in relation to manipulator load capacitymodular configuration ensuring "the perfect fit"
-
Product
Low Capacity Single Point Bending Beam Load Cells
LSP SERIES
-
The LSP Series is a low capacity, low cost, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The LSP Series features a moisture proof sealant.
-
Product
Single 16-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-003
-
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
40 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3710
-
The aTCA-3710 is a high performance, high bandwidth, 40G Fabric switch blade for AdvancedTCA® platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controller, DPI/security network, IPTV, IP multimedia subsystem, RNC/BSC, broadband access/bearer network, data center, and LTE/4G network applications. The aTCA-3710 provides 40GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
Product
PXI 64-Channel Digital Output Module
40-412A-021
-
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
Crossed Roller Rail Sets
-
Del-Tron’s crossed roller rail sets (or crossed roller bearings) are compact, precision rail sets that can support and guide high loads with high accuracy, excellent repeatability, and low friction. A complete range of profiles are offered with roller diameters ranging from 1.5mm up to 6 millimeters, providing load carrying capacities to 2800 lbs. For vertical applications or applications involving high acceleration or deceleration forces you may want to consider our Anti-Creep crossed roller rail sets.
-
Product
Arc Ingintion Tester
-
The product is designed to carry out Arc Ignition Test as per IS/IEC 60947-1 Clause 8.2.1.1.2 (material used for electrical products). The adjustable current source is 230V AC @ 33A. The load is adjusted to get 32.5A at 0.5 power factor. Included on control unit are Digital Voltmeter, Digital Ammeter, Digital Power Factor Meter and Micro Controller based programmable Sequence Timer with LCD display for display & setting. The arrangement is made to mount the test piece with electrodes as per the specification given in the standard.
-
Product
ST Connectors
FY7
-
A straight tip or ST connector is characterized by its quick release bayonet style lock and spring loaded ferrule to hold the fiber. Most commonly used in network applications such as LANs, and Data Processing Networks, they are also found in Premise installations and Instrumentations applications. Horizontally mounted simplex and duplex adapters are available with metal or plastic housings.
-
Product
Pulsed SMU Systems
-
AMCAD Engineering has created professional, industry-proven pulsing technology for both pulsed-bias load pull (Pulsed Load Pull, PLP) and 50ohm transistor test applications. Systems come equipped with a mainframe controller which includes integrated power supplies and integrated input pulser with ±25V/200mA capability. The external output pulser module (probes, pulsers) is configured for 120V/30A pulsing.
-
Product
Linear Testfixture (Cassette Not Included), UTT 105 x 170 mm
MG-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (1000N) 650 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 105 x 170 mm (wxd)• Outer dimensions: 254 x 400 x 50 x 140 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
4-in-1 OSLT Calibration Kit, DC to 40 GHz, 2.92 mm (m)
CK562A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
CPCI or PXI DPFS Board
MS 1830
-
- Configurable Frequency Ranges from 100Hz to 1MHz- Resolution insteps of 0.03Hz- Duty Cycle 50%- Amplitude of the Digital Frequency out : Low – 0.4V max, High – 4.8V min- Rise/Fall Time (for a 15pF Load) is typically 5 ns- Amplitude of the Analog waveform out : Low – 0.4V max, High – 4.8V min- Sinusoidal or Square Wave Output (Configurable)- Differential / Single Ended Output (Configurable)- Frequency on each of the 8 Channels are individually Programmable- Hot Swap Facility for live insertion and removal of the board- Facia plate with Micro Switch Assembly, provided for proper insertion / easy removal of the Board- BNC Connector Interface for Signal Output at the front panel- Each Output Channel is driven by a Cable Driver to drive 8m of Coaxial Cable- Driver interface for Windows XP/VISTA/7 and LINUX OS
-
Product
Industrial Weighing - Wireless Load Cells
-
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
Product
GPIB User Installable Interface Module
EL34GPBU
-
EL34GPBU GPIB user-installable interface (SCPI-1999, IEEE 488.2) module adds a GPIB interface to your EL30000 Series bench electronic load.
-
Product
3U VPX 1 Slot P&G with VITA 67.2 installed in J2
1900002759-0000
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
PXI 16xSPST 16A Power EMR Module
40-161-001
-
These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
4500~6000W DC Electronic Loads
JT634 Series
-
Nanjing Jartul Electronic Co., Ltd
JT634 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT634 series load very suitable for testing power supply when produced in large quantity. Besides, JT634 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT634 series load satisfing most of R&D requirements. Moreover, JT634 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
Product
LED Driver Aging Rack
LEDRACK-100W192P
-
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
