Wafer Level Reliability
-
Product
Signal Level Meters
-
The SignalScout (SS40) provides fast and accurate measurement of signal strength when tuning an antenna for a local TV channel.
-
Product
Sound Level Calibrator
511E
-
Accepted internationally 1 kHz represents the "0 dB" reference point of A, B, C Weighting and other filters utilized in acoustic measurement. The Pistonphone - a mechanical sound source - offers a slightly higher degree of accuracy at a substantial increase in cost. In addition, the 200 or 250 Hz operating frequency is mechanically limited and not suited for measurements of filtered inputs. The 0.2 dB accuracy is quickly lost in the 0.7 to 1.5 dB tolerances acceptable for weighting filters at frequencies around 250 Hz.
-
Product
Wafer Internal Inspection System
INSPECTRA® IR Series
-
An infrared internal defect inspection system has been added to the INSPECTRA® series.It is now possible to inspection with both infrared and visual light in one system.
-
Product
Bi-Directional Level Translator
IFB-10001
-
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
Product
Wafer Edge Profile Measurement
WATOM
-
WATOM can carry out fully automatic, non-contact measurements of the edge profiles and diameter in accordance with SEMICON standards. A special feature is the system's ability to make measurements of the mark cut into the edge of the wafer to indicate the crystal orientation. Because of its high measurement accuracy of less than 1.5 µm, leading wafer manufacturers across the world use WATOM for shop-floor geometrical quality control.
-
Product
Sound Level Meter
-
Maschinenbau Haldenwang GmbH & Co. KG.
Ideal sound level measuring device for almost every acoustical environment.
-
Product
Level Measurement
-
In continuous level measurement, the level of a medium in a tank or silo is detected with the help of different measuring methods and converted into an electronic signal. The level signal is either displayed directly on site or incorporated into a process control or management system.
-
Product
WAFER MVM-SEM® E3300 Series
E3310
-
The E3310 is a WAFER MVM-SEM®* for next generation wafers, supporting 1Xnm node process development and volume production at the 22nm node and beyond. With its high-speed carrier system employing a dual arm vacuum robot, and low-vibration platform to improve measurement accuracy, the E3310 delivers high throughput and performance for wafer measurements. Its multi detector configuration and unique 3D measurement algorithm also enable stable, high-accuracy measurement of 3D transistor technologies such as FinFET. The E3310 makes a significant contribution to reducing process development turnaround time and improves productivity for next-generation devices.
-
Product
Wafer Sort
-
TestEdge offers complete wafer sort solutions. Our range of wafer sort capabilities demonstrates our ability to handle a wide range of devices and device characteristics. State of the art Electroglas probers Sort experience with high probe count Less than 4 mil pitch on probes Experience with C4 Bump and Aluminum pad Experience on Bipolar, CMOS, GaAs, & SiGe Overhead sort or cable harness sort Microsite testing capability
-
Product
Level Indicators
-
4B has a wide range of radio frequency (RF), rotary paddle and capacitance point level indicators for detecting high, intermediate, or low levels of liquids, powders and free flowing granular solids stored in tanks, bins, silos or other containers. Certain units can also be used as plug or choke detectors in chutes, conveyors and elevator legs.
-
Product
Level Measurement
Level Measurement
-
AMETEK Sensors, Test & Calibration
B/W Controls uses the same advanced magnetostrictive technology as in Gemco products providing high accuracy and reliability for continuous liquid level measurement.
-
Product
Non-contact level measurement
-
We provide reliable continuous non-contact level measurement using ultrasound or hydrostatically by using pressure cells as well as reliable measurement of level detection. Our ultrasonic or hydrostatic level measurement systems reliably and accurately detect the levels of liquid media.
-
Product
Sound Level Meters
-
TES Electrical Electronic Corp.
Super high contrast backlight TFT. Compliant with 1 class 2 standard. Real-time 1/1- Octave and 1/3 Octave analysis. Measurement can be started by internal or external
-
Product
Die-To-Wafer Bonding Systems
-
Several different D2W bonding methods are available and selected depending upon the application and customer requirements. In direct placement D2W (DP-D2W) bonding, the singulated dies are bonded to the target wafer one by one using a pick-and-place flip-chip bonder. Plasma activation and cleaning of the surfaces of the dies on the handler wafer are essential steps for establishing a high-yielding bond and electrical interface between the dies and target wafer. This is where the EVG320 D2W activation system comes in.
-
Product
Sound Level Meter
3310 SL
-
Standard Electric Works Co., Ltd
Max. & Min. function. Over & under range indication. 4-digit LCD. Frequency weighting characteristic for 2 times per second. AC signal output. Low battery indication. Auto power off (10 minutes). Backlight function. 200 measurement results can be saved in the memory and recalled on the display. ● Indication of date, time.
-
Product
Wafer Thickness Measuring System
WT-425
-
Contact type can measure any materials within 0.2 µm (2 σ at 20℃ ±1℃). The wafer floats positions while measurement points change and it does not damage even thin wafers. Best for the process control of compound wafers and oxide wafers. (SiC, GaN, LT, Sapphire and Bonded Wafers)
-
Product
Water Level Instrument
-
HighReach Measuring & Controlling System Co.,Ltd
For long time measuring water depth(pressure) and temperature.
-
Product
Level Translators
-
ADI’s level translators offer the most flexible level translation solutions in the industry. The ADG3241 series translators allow direct 3.3 V to 1.8 V translation by means of the innovative SEL pin function while allowing bidirectional data transfer. The ADG3231 series allows wide range 1.65 V to 3.6 V translation and the ADG3308 series allows the industry's widest 1.2 V to 5.5 V up or down translation while permitting bidirectional data transfer.
-
Product
Levels And Protractors
-
Reads either actual level or a relative angle between two surfaces.
-
Product
Semi-Automatic Contactless Wafer Detector
NCS-200SA
-
Semi-Automatically, non-contact measurement of wafer thickness, TTV ,bow,Point and flatness.Portable and easy to set-up, the Proforma 300/G measures all wafer materials including Silicon, Gallium-Arsenide, Indium-Phosphide and wafers mounted to sapphire or tape.the powerful software can test all the data above within several seconds,all the design according to SEMI standard and the ASTM,make sure the data can be easily unify. the system can used for several sample size,like 75 mm, 100 mm, 125 mm, 150 mm, 200 mm
-
Product
Wafer Mapping Sensor
M-DW1
-
Panasonic Industrial Devices Sales Company of America
To provide better safety and improved sensing accuracy, Panasonic studied the requirements for future Wafer Mapping Sensors to ultimately develop the LED Beam Reflective Type Wafer Mapping Sensor, M-DW1. This Sensor uses LEDs as a light source for safe operation and a 2-segment receiving element for higher accuracy in wafer detection.
-
Product
Photodiode Burn-in Reliability Test System
58606
-
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
Sound Level Monitor
-
McLennan Sound Monitoring, Inc
McLennan Sound Monitoring, Inc. offers two unique single-ranged instruments. For high sensitivity areas 41dBA – 101dBA range, and a standard range of 61dBA – 121dBA. A whisper from two feet will activate the 41dBA LED. Normal human conversation ranges from 60 – 80 dBA. Low level talk from two feet will activate the 61dBA LED.
-
Product
Wafer Prober
Precio XL
-
Fully automated 300mm wafer prober. The system achieves high productivity, excellent contact performance, improved cleanliness, and short lead time, and offers a number of high value-added functions as options.
-
Product
Wafer Testing
Trio Vertical
-
SV TCL's TrioTM is a reliable solution for advanced wafer testing challenges, specifically full array and parallel probing. We offer a complete line of vertical probe card products, each designed for your unique application.
-
Product
Sound Level Meters
-
PeakTech Prüf- und Messtechnik GmbH
This digital sound level meter with LCD display and function symbols offers manual range selection in 2 measuring ranges. The fast / slow switching as well as the measured value and maximum value holding function and the internal circuit for checking the calibration (94 dB) emphasize the versatility of this device.
-
Product
Sound Pressure Level Meter
Castle Sonus GA116E
-
The Castle Sonus GA116E Sound Pressure Level Meter is the ideal handheld instrument for all your environmental noise measurements to BS 4142:2014 standard for Rating and Assessing Industrial and Commercial Sound.
-
Product
MPI PA Wafer Probers
-
MPI Photonics Automation is the industry-leading provider of turnkey wafer test and measurement solutions. We offer a complete line of high-performance wafer probers designed to address the diverse and complex needs of the Photonics, Optoelectronic, Semiconductor, and Laser industries.
-
Product
Thermal Dispersion Level Switches
-
ABB's Thermal Dispersion products can be used for flow, level or temperature detection. One switch can be field configured to detect one of these three process conditions.
-
Product
Solar Wafer Transfer Tool
-
Dou Yee Enterprises (S) Pte Ltd
Dou Yee Enterprises Solar Wafer Transfer Tool
