Device Under Test
a specific purpose component or module check; ex. substantial component of a PCB.
See Also: DUT, Unit Under Test, EUT
-
Product
Multi-Channel Attenuation Control Unit (5-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7205B
Attenuator
The J7205B is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to 5 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205B reduces cost of ownership and provide the best measurement accuracy.
-
Product
Long Wavelength Optical Spectrum Analyzer 1200 To 2400 Nm And 1000 To 2500 Nm
AQ6375E
-
Due to the high resolution and sensitivity of the AQ6375E, it can actually detect the presence of water molecules in the air. The water vapor is detected in the upper Near-IR wavelength region and could overlap with or mask the spectral characteristics of the actual device under test in that particular region.
-
Product
GONIOPHOTOMETRY
-
Goniophotometers are required to measure angular resolved distributions of photometric or colorimetric quantities, either by rotating the lighting device under test or by moving the sensor around the device. Depending on the application, different geometries are used to obtain distributions in the appropriate CIE coordinate system.
-
Product
2-Axis Rate and Position Tables
-
When a device under test needs to be stimulated with simultaneous movements around two axes, then a product from the ACUTRONIC two-axis motion simulator range is the right choice. Due to their independent motion simulation in two axes they are very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
Product
Power Quality Analyzer
PQM-711
-
PQM-711 power quality analyzer is an advanced product for wide type of measurements, analysis and recording of network parameters 50/60 Hz and the power quality diagnostic according to European standard EN 50160. PQM-711 is an innovative model with a wireless communication Wi-Fi , which allows for automatic pairing with the included tablet, with a large 10" touch screen. Tablet allows full operating of the analyzer, live data preview and the reading and analysis of data stored in the internal memory. With this solution, the PQM-711 is an unique device that combines the advantages of the analyzer with built-in display and typical portable analyzers (known as Black Boxes).With the tablet you can very fast checked the device under test. On the other hand, you can leave the analyzer module for multi-measurements as a typical logger without display. You can very fast diagnose the machine under test using the tablet. On the other hand, you can leave the analyzer module itself for many days measurement as a typical logger without display. PQM-711 has a transient registration with a maximum sampling rate of 10 MHz (rapid changes in voltage) and control signals. The minimum duration of the registered transient is 650 ns.
-
Product
Spring Probes
Spring Probe
An essential component in the testing of electronic components. In Test & Measurement applications, they are used to make contact with test points, connecting the DUT (device under test) with the test equipment.
-
Product
PCIe 6.0 Protocol Analyzer
P5570A
Protocol Analyzer
Keysight PCIe 6.0 Protocol Analyzer redefines protocol debugging and validation through a new innovative CEM card form factor, bringing vast improvement in signal integrity and equalization with instant link-up to systems as well as devices under test
-
Product
PXIe-4145, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit
782435-01
Source Measure Unit
PXIe, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit - The PXIe-4145 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4145 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4145 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
Single Board Source/Meter/Switch
SMSU
-
SMSU Series SourceMeterSwitch Unit (SMSU), introduced by SW Link Ltd, is single-channel voltage/current sourcing, 4X6 switch matrix and measurement instruments. Each Series 100 SMSU instrument tightly integrates highly accurate stable DC power source and a true instrument-grade programmable gain amplifier and 18bits ADC on a 100x100mm PCBs. It can output up to 20V, sub-uA to 1A current to device under test (DUT)
-
Product
PXI Battery Simulator 2.8 Amps
41-753-001
Simulator
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
Shock Testing
-
Shock testing typically involves calibrated, repeatable, violent events. The resulting energy is then absorbed transferred through the test specimen or Device Under Test (DUT)
-
Product
CAN MiniModules
-
Measurement points distributed throughout a device under test, whether in a vehicle or at a test bench place high demands on the measurement technology. Measurement modules must be compact, robust, reliable, and easy to use. CSM meets all these requirements with its long-term proven CAN MiniModule series.
-
Product
Performance Board
-
The role of the performance board is accurate transmission of tester signals all the way to the device leads. Custom performance boards from ADVANTEST deliver support for DUTs (devices under test), as they become faster and smaller, with greater pin counts, and increasingly take the form of SMDs. ADVANTEST performance boards also support a host of test requirements, such as analog test, high-speed performance, and high-density, for testing state-of-the-art ICs.
-
Product
Modular Power
RFP DC High Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
Regenerative Power System, 950 V, 20 A, 10 kW, 400/480 VAC
RP7963A
DC Power Supply
The RP7963A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test. The regenerative capability enables the energy normally consumed to be returned to the grid cleanly, saving costs associated with energy consumption and cooling.
-
Product
sbRIO-9229 , Non-Enclosed, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
780874-01
Voltage Input Module
Non-Enclosed, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9229 performs differential analog input. The sbRIO‑9229 is an effective general-purpose analog module because of its resolution, sample rate, and input range. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Non-enclosed modules are designed for OEM applications.
-
Product
Qualification Tester
LQ402
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 6 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 2 cabinets. One is for the electronic components with the primary measurement devices and the other one holds the 6 load boxes.
-
Product
256 Channel Power Supply
IDPS750
-
Salland Engineering’s Independent Device Power Supply (IDPS) can expand your existing Automated Test Equipment (ATE) with up to 256 independent DPS sources to increase parallel testing. It offers Force Voltage (FV) and Measure Current (MI) that can be used for continuity tests, parametric supply current (IDD) and quiescent supply current (IDDQ) measurements or simply for powering devices under test. The IDPS750 is targeted to reduce test costs for a wide range of applications including smart cards, memory, microprocessors and FPGA’s. Its design makes it useful in applications where many resources are required, or were the original ATE supplies do not meet your required specifications.
-
Product
Optical signal transmission
Digital
-
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
Product
Regenerative Power System 2000 V, ±30 A, 30 KW, 400/480 VAC
RP7983A
DC Power Supply
The RP7983A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
Regenerative Power System, 160 V, ±125 A, 10 KW, 200/208 VAC
RP7936A
DC Power Supply
The Keysight RP7936A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
PXIe-4140, 4-Channel Source Measure Unit
781742-01
Source Measure Unit
The PXIe-4140 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4140 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules.
-
Product
Large-size Hybrid Reverberation / Anechoic Chamber
F-Series
-
The F large-size hybrid Reverberation/Anechoic Chamber represents the most versatile OTA test system in the market today. With the same unique test features of their E Series RC counterparts, the F-Series can also test large form-factor devices under test (DUTs) like laptops, large TV sets, solar and trash compactors, drones, fridges or washing and vending machines, among others. With up to 16x16, 8DLCC and DUTs up to 2m and 500 kg including full-body phantoms in a turntable, the F Series also expands the frequency range down to cover 200 MHz up to 40 GHz frequency ranges and the test modes to include EMC, BS, small cell, eNodeB and Virtual Drive Testing over the air (VDT-OTA). In an again unheard-of feature, the F-Series is also reverse-convertible into an Anechoic chamber, allowing Far Field (FF) and Spherical Near Field (SNF) radiation patterns, efficiency and gain measurements and pre-5G testing of antennas and devices. Conversion from RC to AC or vice versa can be performed within half a day.
-
Product
Mini Burst Field Generators
-
Mini burst field generators are small and handy burst generators used to detect weak spots in the device under test.
-
Product
PCIe 6.0 Protocol Test Backplane
P5563B
Backplane
The Keysight P5563B PCIe 6.0 Protocol Test Backplane provides a convenient means for testing PCIe 6.0 add-in cards with a self-contained portable and powered passive backplane. The P5563B provides power required for all combination of exerciser and analyzer with device under test.
-
Product
Function Tester with Low Number of Channels
UTP 6010 RF
-
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels and integrate the necessary interfaces directly in the adapter or tester. The test speed, production volume and overall complexity of the UTP 6010 interfaces can be varied according to your requirements.
-
Product
NI-9239, ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
779593-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the NI‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range.
-
Product
Digital Leakage Current Tester
-
Educated Design & Development, Inc.
Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.
-
Product
Water Brake Engine Dynamometers
Hydraulic Dynos
-
Ideal for a wide range of markets, water brake engine dynamometers churn water inside the housing and transfers energy by momentum exchange and water shear. The more water flowing through the dyno, the greater the braking force exerted on the device under test.
