Device Under Test
a specific purpose component or module check; ex. substantial component of a PCB.
See Also: DUT, Unit Under Test, EUT
-
Product
Keysight Dual/Quad 4x8 Reed Matrix for 34980A
34933A
Matrix Switch Module
The Keysight 34933A module for the 34980A Multifunction Switch/Measure Unit gives you the most flexible connection path between your device under test and your test equipment, allowing different instruments to be connected to multiple points on your device under test at the same time. Dual 4x8, 8x8, or 4x16 2-wire configurations 64 2-wire or 128 1-wire cross-points High-speed reed relays Connections to the internal DMM Expandable via four 2-wire analog buses Relay counter ±150 V peak, .5 A switch, 1.5 A carry current
-
Product
Logic Analyzer Probes
-
Three probe types are available for GoLogicXL logic analyzers: flying leadset, Mictor, and Pinpoint probes. The Mictor and Pinpoint probes are compatible with similar Keysight/Agilent "soft touch" and Tektronix "connectorless" probes. All GoLogicXL probes are coaxially shielded and use passive termination inputs to prevent loading the device under test. Both differential and single-ended input signals are supported by all probes. Input voltage swings small as 300 mV are supported in single-ended mode, and 150 mV for differential signals.
-
Product
Regenerative Power System, 160 V, ±125 A, 10 KW, 400/480 VAC
RP7946A
DC Power Supply
The Keysight RP7946A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
Automatic Calibration Module
ACM2509
-
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full two-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to seven connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
Product
External Frontend
FE44S
-
The R&S®FE44S external frontend can extend the frequency range up to 44 GHz for Rohde&Schwarz signal and spectrum analyzers as well as signal generators. The R&S®FE44S enables signal up and downconversion directly at the device under test (DUT), lowering cable losses, increasing sensitivity and delivering more power at the antenna in an OTA environment. The R&S®FE44S uses a single RF connector to further reduce the number of antennas in over the air testing.
-
Product
PXI-2547, 2.7 GHz, 50 Ω, 8x1 PXI RF Multiplexer Switch Module
778572-47
Multiplexer Module
2.7 GHz, 50 Ω, 8x1 PXI RF Multiplexer Switch Module—The PXI‑2547 is an RF signal multiplexer switch module. The higher channel count of the PXI‑2547 makes it ideal for test systems that require the switching of a large number of RF signals, such as switching several devices under test to a single channel on the RF analyzer. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
Multi-Channel Attenuation Control Unit (4-channels), DC to 6 GHz, 0 to 121 dB, 1 dB Step
J7204A
Attenuator
The J7204A is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 6 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204A reduces cost of ownership and provide the best measurement accuracy.
-
Product
PXI Power & Sense Multiplexer, 2-Pole, 18-Channel
40-658A-002
Multiplexer Module
The 40-658-002 is a PXI multiplexer combining a 2-pole 18-way power distribution MUX with a second lower power 2-pole 18-way MUX in a convenient single slot PXI module. It is ideal for power distribution where power and sense signals are required to be connected to an array of devices under test.
-
Product
1kV, 120 MHz High Voltage Differential Probe Without Tip Accessories and with Auto Zero Disconnect
HVD3106A-NOACC
Differential Probe
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
Line-impedance stabilisation network
NNB 21 set
-
The NNB 21 line impedance stabilization network is designed for measuring of grid bound interferences of a device under test according to the satndard CISPR 25/ISO 7637. It measures the RF interference, which couples into the vehicle electrical system. Measurements during the development in a frequency range from 100 kHz to 1GHz can be carried out.
-
Product
4-Quadrant General-Purpose Source/Measure Unit, ±20 V, ±1 A Or ±6 V, ±3 A, 20 W
N6784A
Source Measure Unit
The Keysight N6784A is a source/measure unit (SMU) designed for general-purpose precision sourcing and measurement. General-purpose applications can span many different industries and many different devices under test (DUTs). The N6784A SMU is a versatile tool designed to tackle many of these general-purpose applications. Its glitch-free operation ensures safe usage with the DUT during output and measurement range changes, even with capacitances of up to 150 µF. Its 4-quadrant operation enables it to act as a bipolar power supply or a bipolar electronic load, for added versatility. When using the N6784A SMU, engineers can be confident that they have an all-around general-purpose tool for their test systems or lab bench.
-
Product
PXI 18 Channel Data Comms MUX, 96-pin SCSI
40-735-902
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
Medium-power DC Electronic Load (900W~6000W)
FT6400A Series
-
Shenzhen FaithTech Technology Co., Ltd.
The FT6400A series has modular design, with strong adaptability, high reliability and high maintainability. Mainly used in power electronics testing fields such as power batteries, medium and high power DC power supplies, DC generators, etc. The FT6400A electronic load not only provides OCP, OVP, OPP, OTP, RVP but also provides Von and Voff functions and programmable protection functions for the device under test. These features can greatly improve the reliability of the product, and it is a reliable product for engineering test and automatic test system integration.
-
Product
Functional Test
xUTS
Functional Test
Extend test to encompass copious test points and DUT varieties along with real-time, hardware-in-the-loop and other state-of-the-art instrumentation. extendedUTS (xUTS) is a custom product for high complexity functional test. Configured for the unique needs of a class of devices under test (DUTs), the xUTS employs our universal test system approach that combines the best open platform instrumentation and software along with mass interconnect technology.
-
Product
NI-9229, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module
780180-01
Voltage Input Module
±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module - The NI‑9229 performs differential analog input. The NI‑9229 is an effective general-purpose analog module because of its resolution, sample rate, and input range. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating.
-
Product
Test Port Adapter Set, 3.5 Mm (Test Port) To Type-N
85130C
-
The Keysight 85130C test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to type-N male adapter and a 3.5 mm to type-N female adapter. The frequency range for these adapters is dc to 18 GHz with a return loss of 28 dB or better.
-
Product
Customized Test Fixtures
-
Test fixture is a device designed to mount a device under test (DUT), equipment under test (EUT) and unit under test (UUT) in place and allow it to be tested by being subjected to controlled electronic test signals and procedures.
-
Product
DC Automated Accelerated Reliability Test Station (AARTS)
DC-HTOL
-
The DC Automated Accelerated Reliability Test Station (AARTS) systems are designed to maximize channel density. The first systems developed by Accel-RF (ARF) were intended for RF and DC stimulus to the Device Under Test (DUT). However, there are some applications in which RF stimulus is not required.
-
Product
Pulse Function Arbitrary Noise Generator
81160A
Arbitrary Waveform Generator
Generation of 330-MHz pulses and 500-MHz function/arbitrary waveforms with a 2.5-GSa/s sample rate and 14-bit vertical resolution; Selectable crest factors for white Gaussian noise lets engineers determine how much distortion to apply to a device during stress testing to meet various serial bus standards; Glitch-free timing parameter changes allow engineers to change the frequency without drop-outs or glitches and enable continuous operation without rebooting or resetting the device under test; and Arbitrary bit patterns show capacitive load of the channels using simple pattern settings. Complex measurement setups are no longer necessary to test designs to their limits. Pulses 330 MHz, 500 MHz sine waves, 660 Mbit pattern
-
Product
Dynamic Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
Digital I/O Module
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Product
Qualification Tester
LQ404
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 12 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 3 cabinets. One is for the electronic components with the primary measurement devices and the other two hold the 12 load boxes.
-
Product
Regenerative Power System, 500 V, 20 A, 5 kW, 200/208 VAC
RP7951A
DC Power Supply
The RP7951A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test. The regenerative capability enables the energy normally consumed to be returned to the grid cleanly, saving costs associated with energy consumption and cooling.
-
Product
Mass Interconnect
-
Mass interconnect is a way of connecting test instrumentation to a device under test (DUT). To put it simply, mass interconnect is a very large plug and socket which connects your device under test to your test instrumentation without the mess and hassle of having to connect each signal separately.
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
Artificial Power Supply Network
KH3763
-
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
Product
Pod/Nest Fixtures
-
Nest and Pod Fixtures are used to test components and sub-assemblies. They typically are built in an array and the devices under test are subjected to tests that simulate operating conditions or life-cycle testing. Test Head Engineering is experienced in providing nest and pod testers that meet the connectivity, ergonomic and mechanical requirements of component testing.
-
Product
PXI-2559, 2.5 GHz, 75 Ω, Dual-Terminated SPDT PXI RF Relay Module
778572-59
Relay
2.5 GHz, 75 Ω, Dual-Terminated SPDT PXI RF Relay Module - The PXI‑2559 is a general-purpose switch module featuring two independently terminated single‑pole double‑throw (SPDT) relays. You can use it to add flexibility to your video switch network or to maintain uniform signal paths across multiple channels when building high-channel-count multiplexers. The PXI‑2559 termination resistors minimize reflections on open channels and protect your source or device under test from damage. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
Prototyping & Test Consulting Services Solutions
test
Don’t cut corners on the path to quality. We are experts in Design for Test (DFT), Design for Manufacturing (DFM), agile development, prototyping and standards/best practices in many industries. Speak to our prototyping and consulting services experts to ensure you make the right decisions and investments at the start of your project.
-
Product
TestStand
test
TestStand is industry-standard test management software that helps test and validation engineers build and deploy automated test systems faster. TestStand includes a ready-to-run test sequence engine that supports multiple test code languages, flexible result reporting, and parallel/multithreaded test.
-
Product
NI Real-Time Test Cell Reference System
778820-35
test
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
