-
Product
Probes
-
Without breaking the circuit, AC Current Probes convert the current within a conductor into a voltage measurement for display on an oscilloscope or voltmeter. Our AC or AC/DC clamp current probes feature jaws that can close around the electrical conductor. There’s no need for disconnection or physical contact. Transcat offers the latest in current and clamp-on probes designed for applications ranging from electrical utility to industrial maintenance.
-
Product
Microwave Probes
D-Probe
-
With only two signal pins, D-Probes can perform accurate measurements without the need of nearby ground pads.
-
-
Product
Reflection Probes
-
Reflection probes are used to obtain spectral information of diffuse or specular materials. The light from a light source is sent through six illumination fibers to the sample, and the reflection is measured by a 7th fiber in the center of the reflection probe tip. Discover our reflection probes below.
-
Product
ICT Probes
Merica Series-MPA75
-
Minimum Center: 1.91 (75mil)Current Rating: 3amps, continuousCurrent Resistance: 40milliohmsMounting Holes Size: 1.35Full Stroke: 6.35mmRated Stroke: 4.30mmSpring Force: 198gf(7oz)
-
Product
Power Probes
RkT Thermopile Series
-
The RkT Series thermopile power probes are ideal for measuring Nd:YAG, CO2, and other mid-power lasers. The probes are designed to withstand average power densities up to 20kW/cm2 (15MW/cm2 peak pulse power density). The flat UV to far-IR spectral response allows the probes to measure broadband sources as well. Measure the power of cw sources or the average power of sources pulsed at 5Hz or greater.
-
Product
Active Voltage Probes
-
Engineers must commonly probe high-frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. Active voltage probes feature both high input R and low input C to reduce circuit loading across the entire probe/oscilloscope bandwidth. With low circuit loading, and a form factor that allows probing in confined areas, the active voltage probe becomes the everyday probe for all different types of signals and connection points.
-
Product
TSP138 Switch Probes
-
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
Product
Active Probes
-
To ensure that as much information as possible is available at your fingertips, the IOM6 Hub can be used to increase the number of FNet ports on the iC5700 BlueBox by 4. Now you can combine our CAN/LIN data capture, analog and digital capture and control, and debug and trace all from one central hardware tool via our Active Probes
-
-
Product
Gold Probes
4900 Series
-
The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.
-
-
Product
Probes
70 Series
-
American Probe & Technologies, Inc.
The series is for all probes that are non-standard in shank diameter (other than 10 or 20 mil).
-
Product
Trident Fiber-Optic Probes
-
Our most popular and cost-efficient option for the test of multiple LEDs — testing three LEDs with a single Sensor. This method of testing LEDs scales up, so that testing 3, 30, 300 — or any number of LEDs — is far more cost-efficient than other methods. This is our most popular Fiber-optic Probe and can be combined with any of our Universal LightProbe Sensors.
-
Product
Hall Effect Probes
-
Magnetic Instrumentation manufactures Hall Effect Probes in a wide range of styles and sizes. Probes are supplied with magnetic, electrical, temperature stability and calibration data for each measurement range.
-
Product
Spring Probes
-
Spring probes are designed to optimize performance in high reliability, multicycle applications. Smiths Interconnect's spring probes, featuring IDI contact technology, are compliant which makes them ideal for blind mate applications as they self correct for x, y, z, rotational and angular misalignment of the target. Offered in compressed heights less than 2 mm and utilized on pitches as tight as 0.4 mm, they are well suited for high density, board-to-board, battery contact and high frequency applications.
-
Product
Handheld Probes
-
Used for manual inspection, maintenance, and other ad-hoc temperature measurements, these probes come in a variety of handle designs to meet your different ergonomic preferences and application needs.
-
Product
CCA-006 Battery Probes
-
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 78Full Travel (mm): 1.98Recommended Travel (mil): 40Recommended Travel (mm): 1.02Overall Length (mil): 669Overall Length (mm): 16.99
-
Product
Bulk Current Injection Probes
-
The Com-Power CLCI-100 and CLCI-400 are precision bulk current injection probes designed for conducted immunity testing. The CLCI-100 covers 10 kHz to 100 MHz, while the CLCI-400 extends up to 400 MHz and complies with MIL-STD-461 and RTCA DO-160. Both models feature split-core ferrites for easy cable insertion and are compatible with calibration fixtures for accurate RF injection and monitoring.
-
-
-
Product
High Impedance Active Probes
7A
-
An unterminated version, can be used for capacitance and resistance measurements or in low to medium speed signal applications where a 50 ohm termination is not required. A flexible coaxial cable length of 6 feet in length is standard on the Model 7A; however, when used for capacitance measurements, GGB Industries, Inc., recommends using a shorter 3 foot cable. If a shorter length of cable is desired for capacitance measurements, please specify it when ordering (Model 7A-3ft.). Please note that Model 7A uses Model 7 replacement tips.
-
Product
Power Rail Probes
-
Optimized for power integrity measurements, these probes combine low noise contribution, DC offset up to 60 V, high bandwidth, low loading, and a wide range of connectivity alternatives.
-
Product
BARE BOARD TEST PROBES
-
Probe Technical DataMechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current60 18 mOHMS mean63 60 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper60 24 Kt gold plated over nickel63 24 Kt gold plated over nickelBARREL: Nickel silver60 24 Kt gold plated ID and OD over nickel63 No FinishSPRING: Music Wire, 24 Kt gold platedover nickel
-
Product
High Impedance Active Probes
12C
-
A high speed, high input impedance active probe for measuring the internal node voltage of integrated circuits. The input is 1 megohm shunted by 0.1 pf and the rise/fall times are 0.8 ns. This instrument has full dc capability and can be used with any oscilloscope. The Model 12C was specially designed so that when used in conjunction with a high input impedance oscilloscope, signal attenuation is 10:1 and with a 50 Ohm input, signal attenuation is 20:1.
-
Product
DDR4 MSO Probes
-
The DDR4 DIIM and SO-DIMM Mixed Signal Interposers connect Address, Command and Control signals of a DDR4 bus to the Keysight V-Series Oscilloscopes with the MSO option. These interposers also provide accessibility to DDR4 signals for convenient analog probing. The user can then easily observe both the digital and analog representation of the DDR4 Address, Command and Control bus. Solder down N5541A analog probes purchased separately from Keysight Technologies.
-
Product
Optical Probes - Low Bandwidth
-
Depend on Tektronix to provide you with performance you can count on, and industry-leading service and support.*Broad Wavelength Response 500 to 950 nm or 1100 to 1700 nm*High-bandwidth DC up to 1.2 GHz*High Gain 1 V/mW*Low Noise <11 pW/√Hz*Probe Connects to DPO7000*1 and DPO/DSA/MSO70000*2Series*SONET/SDH and Fibre Channel Reference Receiver Performance
-
Product
Transducers and Probes
-
Olympus NDT probes and transducers are high-quality inspection equipment available in a range of frequencies, configurations, connection styles, and cable types. All our probes and transducers are lightweight but solidly constructed.
-
Product
Conical Laser Power Probes
-
Conical Head Power Probes are used to measure high power density CO2 laser beams which may damage the standard flat surfaced Power Probes. The conical absorbing cavity exhibits a high heat dissipation.
-
Product
High Voltage Differential Probes
-
High voltage differential probes provide high CMRR over a broad frequency range (up to 400 MHz) to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.
