Static Electric Field
is a stationary charge that is time invariant.
-
Product
Flat Field and Imaging Gratings - Type IV
-
HORIBA Scientific produces a wide range of holographic master gratings from which high precision replicas are manufactured.Type IV aberration-corrected flat field and imaging gratings are designed to focus a spectrum onto a plane surface, making them ideal for use with linear or 2-D array detectors.These gratings are produced with grooves that are neither equis-paced nor parallel, and are computer optimized to form near-perfect images of the entrance slit on the detector plane.
-
Product
Electric Torque Screwdrivers
CL-Series
-
The CL-Series is electric torque screwdriver that is designed for heavy-duty production and delivers reliability and precision torque. Tool offers proven performance and ensures accuracy in fastening with precision automatic shut-off clutch once preset torque is achieved.
-
Product
Electrical Testing
-
Board defects are never an option. Your customer expects perfect boards, each time, every time. Electrical testing is the key in ensuring that the connectivity of a PCB is precisely as specified and that there are no defects or flaws that may cause problems down the line.
-
Product
FM/ATEX Approved Static Discharge Cable Reels
Cen-Stat Static Discharge Reels
-
Retracting cable reels are an alternative solution to using retractable Cen-StatTM spiral cable. They are normally specified for locations where there is a preference for ensuring process operators stow grounding clamps correctly for good "housekeeping" purposes when the clamps are not in use.
-
Product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
-
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
Product
Field Testing
-
Electronic force measuring device with digital display in MN / m², switchable for load plate.
-
Product
Electrical Safety Test Scanner
19200
-
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
Product
Active Loop Antennas / Magnetic Field Probes
-
Is an active, shielded handheld loop antenna with nearly con- stant antenna factor over the entire frequency range. It can be used for testing according to CISPR, MIL, FCC, EN, ISO, ANSI, ETSI and many other standards.
-
Product
Field Communicators
-
We offer modular multi-bus field communicators for HART, FOUNDATION Fieldbus H1 and Profibus PA protocols, combined in some of our process calibrators. While the communicator is built in the same device with the process calibrator, they can communicate seamlessly offering better user experience than separate calibrator and communicator. Plus you only need to carry one device. Thanks to the modularity you can select which protocol you take, and update more protocols later on, if needed.
-
Product
LED Thermal and Electrical Performance Analyzer
T5
-
Thermal parameter is the key index to evaluate the performance of LED. It’s very important to measure thermal characteristics of high power LED for high reliability LED applications. It will have effect on the optical parameters, electricity parameters and lifetime of LED. Therefore, design and control of the thermal dissipation is the most important thing for the manufacturers and users.
-
Product
Zero Field Cavity
-
Zero field cavities generate a zero magnetic field in an air gap. They are mainly used to calibrate hall probes for their zero scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using Zero Field Cavity.
-
Product
Electrical Grounding Analysis
GroundMat
-
SKM GroundMat is a program for substation ground grid design and analysis. It is designed to help optimize grid design or reinforce existing grids of any shape. It uses a general-purpose finite element algorithm for potential analysis and graphical facilities to validate ground system efficiency
-
Product
Battery Electrical System Analyser
-
We invented the “Resistance method” which uses a series of shorting pulse to measure the voltage drop in order to calculate the plate’s internal resistance. Unlike other patented “Conductance method” which generates an AC pulse across the battery terminal to measure impedance.
-
Product
Static Installations
-
Innovative mounting solutions for maximizing the probability of intercepting Rad / Nuc sources.
-
Product
Electrical Swivels
-
Electrical Swivels enable the rotation of data and/or power cables and are designed to be integrated into the swivel stacks of Floating Production Storage and Offloading (FPSO) applications. They can withstand the typically harsh environments of the oil and gas (O&G) industry and are installed on vessels and/or floating moored platforms.
-
Product
Portable Electrical Management Systems
EMS-LCHW30
-
Progressive Industries Portable Electrical Management Systems (EMS) provide full RV protection against all adverse power conditions. You will feel secure with multi-mode surge, voltage, polarity and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: Voltage(s), current, frequency, error code, and previous error code (if applicable). Replacement parts are simply plug-and-play, making repairs quick and easy. As with our portable models, the computer is driven by state of the art microprocessors. Should the software ever change, EMS owners can receive a free upgrade at no cost.
-
Product
Dual Servo Electrical Test Fixture
TA-334001
-
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
Product
Near Field Probes 1GHz - 10 GHz
SX set
-
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Probes, Magnetic Field
EM-6881 | 480 KHz To 30 MHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
Product
IEC60335-1 Electrical Inclined Plane Device
CX-100
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-1 Electrical Inclined Plane Device is designed and manufactured in accordance with IEC60335-1 clause 20.1. The IEC60335-1 Electrical Inclined Plane Device is to determine the stability of electric appliances which are used on a table or on the floor. The IEC60335-1 Electrical Inclined Plane Device consists of a surface and an angle adjusting device, with angles 0~15° adjustable.
-
Product
Electrical Power Transducers
-
Manufactured for utilities since 1969, TransData Power Transducers are used for measuring AC and DC power variables in Substation, Generation, Load Control and Industrial applications where ±1ma or 4-20mA analog signal are required by the SCADA/Energy Management System. Models are available for measuring Current, AC Voltage, DC Battery Voltage, Watts, VARs, Frequency and more.
-
Product
Portable Electricity Meter Testers
EE-120A-3S + EE-500V-3
-
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. All types of electricity meters – mechanical or electronic, for active, reactive or apparent energy, single-phase or three-phase – can be tested with the Energy Standard. The following meter tests can be carried out with the EE Test System: Error Test, Register Test, No Load Test and Starting Current Test. Full analysis of the customer load can also be performed, if current clamps have been ordered. All test results ( maximum 3 Test Plans, 5 Manual Measurements and Customer Load Analysis) can be saved in one file. 100 saved files can be viewed on the LCD display or transferred to a PC via USB port.
-
Product
Optical & Electrical Data/Pattern Generators
-
The Data/Pattern Generators offer both electrical and Optical outputs with standard and custom data patterns. PPG products cover data rates ranging from 100 Mb/s to 28.05 Gb/s.
-
Product
Multifunction Electrical Installation Meter
AMPI-520
-
The AMPI-520 digital meter is designed to measure impedance in short-circuit loops without tripping the differential protection, it also measures the protection tare, earth resistance, continuity and phase sequence check.
-
-
Product
CHEK 3-in-1 Electrical Tester
GT 3100GAM
-
Cable test monitors line continuity, shows completed circuits. Lamp test indicates the lamp and fixture continuity. Circuit tester checks if power is available, if polarity is correct, if wiring is correct.
-
Product
Flexible Magnetic Field Probes
-
Projekt Elektronik Mess- und Regelungstechnik GmbH
The active probes are equipped with active amplifier electronics and have an extremely low-impedance output, ie they can also drive long lines. The output signal is calibrated according to specification. They can not only be connected to a certain type of teslameter, but can also be connected to any signal input.
-
Product
Medical Electrical Safety Testers
-
Shanghai Beha Electronics Co., Ltd.
Special purpose AC milliammeter designed to measure hazardous leakage current from electrical appliances and other power line operated equipment.
-
Product
Magnetic Field Logger Sensor
NUL-214
-
This is a very sensitive magnetic fields sensor. It can measure a very low level of magnetic fields such as the magnetic field of Earth.The logger sensor measures the magnetic fields in milli Tesla (mT).
-
Product
Electricity Metering Device
Mk7B
-
Designed for residential and commercial use, the Mk7B can operate in credit or prepayment mode. It has a 100 Amp relay for remote connect/disconnect of electrical services.
