-
Product
Digital Accelerometer
ZET 7052-N
-
Digital accelerometer ZET 7052-N is equipped with a compact sensing element and is designed for linear acceleration and vibration acceleration variable constituent measurement via three mutually perpendicular planes. Small weight of sensing element (1,5 g) considerably reduces self-mass load and compact dimensions (8,5×8,5×8,5 mm) enable use of the digital accelerometer ZET 7052-N for vibration measurements in systems with small active area.
-
Product
Digital/Pattern/PE Card
PE16S
-
The PE16S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE16, the PE16S offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (16 boards). The PE16S offers 16 programmable level input or output channels with 2 PMU . The PE16S also supports deep pattern memory by offering 32 M of on-board vector memory with per channel dynamic direction control running test rates up to 66 MHz.
-
Product
AC Current / Leakage Digital Clamp-on Tester
MCL-500DFN
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
MCL-500DFN AC Current / Leakage Digital Clamp-on Tester
-
Product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
-
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
350 MHz, 2 Analog Plus 16 Digital Channels Oscilloscope
MSOX3032A
-
350 MHz2 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Digital Output
VME-2170A
-
The VME-2170A optically coupled digital output board consists of VMEbus compatibility logic,data control logic, four 8-bit output registers, and 32 optically isolated high-level outputs. The board is implemented as a double Eurocard form factor PC board, and provides all necessary address decoding and data transfer control logic to accept both 8- and 16-bit data transfers. Optical couplers isolate the 32 outputs from each other and from the VMEbus.
-
Product
NI-9375, 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-02
-
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
Digital Panel Meter
-
Shenzhen Star Instrument Co., Ltd.
Three-phase energy meter measures energy, voltage harmonics, current harmonics, voltage, current, power and power factor.
-
Product
Digital Insulation Tester
1550C
-
The Fluke 1550C performs digital insulation testing up to 5 kV, and makes data collection easy through the Fluke Connect™ wireless app. Remote operation lets you spend as little time as possible in potentially hazardous zones.
-
Product
Digital Laser Power Probe
-
The Macken Instruments, Inc., Digital Laser Power Probe is a completely portable, easy-to-use calorimeter type power meter. The instrument consists of two components: a microprocessor-based digital meter and a probe head.
-
Product
Digital RF Power Monitor
3024
-
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
Product
Digital Classical Shock Controller
DVC-4/8 Shock
-
The CSC- I will perform all of the 'classical' shock tests as defined in MIL-STD-810 and is equally useful for environmental qual testing or production test screening. Automatic calculation of pre- and post-pulse compensation assures the maximum performance from your test system.
-
Product
Digital Ethylene Glycol Refractometer
MA888
-
Thousands of cooling tower and recycle professionals from boiling towers to antifreeze recycling move to the digital MA888 Digital Ethylene Glycol meter for measurement of the refractive index to determine the % volume and freezing point of ethylene glycol based coolants or antifreeze, from less precise optical refractometers.
-
Product
Digital Power Meter
66203/66204
-
Chroma 66203/66204 Power Meters are designed for multiple phase power measurement applications. The wiring mode function allows the user to take accurate power measurements for various wiring modes 1P2W/1P3W/3P3W/3P4W as well as providing accurate standard power measurements common for most electrical devices. A unique feature of the 66203/66204 is its stateof- the-art DSP digitizing technology instead of less accurate and slower traditional analog circuits. The internal 16 bits analog/digital converters with sampling rates of up to 250kHz provide both high speed and high accuracy measurements which is unprecedented within the industry for this class of power meters. The instruments include a four part display with 7-segment LED front panel readouts. Users can easily select desired parameters and readouts with a touch of a button. The 66203/66204 meters also include remote control using USB or GPIB interfaces via rear panel connections.
-
Product
Digital Tachometer
RM-1500 /RM-1501
-
5 Digits LCD Display. Light Reflex Measurement. Range from 10.00 to 99,999 RPM. Measuring Distance 50 to 300 mm. Event Counter elapsed time. Max/Min/Hold : True Average
-
Product
Analog and Digital Interface
425
-
Three quadrature encoder channels with 16-bit countersFour 12-bit D/A outputsEight 12-bit differential A/D inputs, 50 kHz rateWatchdog timerForty-eight bi-directional digital signals for solid state relay boardsPC/ISA compatible
-
Product
Digital Multimeter
DMT-4010RMS
-
Monacor International GmbH & Co.
*True RMS measurement method*Dust and water protection according to IP class 67 with covered measuring sockets*Auto ranging for faster measurements*4000 digit resolution*Additional bar display*Voltage measurement up to DC/˜ 1000 V*Current measurement up to DC/˜ 10 A*Frequency measurement up to 10 MHz*Resistance measurement up to 40 MΩ*Capacitance measurement up to 40 mF*Temperature measurement -20 °C to +760 °C*Acoustic continuity test*diode test*Data hold (measured value memory)*peak hold*Maximum and minimum value recording*LC display with switchable background lighting*Automatic shutdown*overload protection*Supplied with test leads and protective case
-
Product
Digital VHDCI Connection and Cables
-
All Spectrum v68 type connections are 68 pole VHDCI connectors. These adapter cables have to be ordered separately.
-
Product
Digital Power Meter (AC Model)
LS2008R
-
• Measure Vrms, lrms, W, PF; • Voltage range: 10-600v, Current range: 0.005-20A ; • Accuracy: ± (0.4%reading + 0.1%range + 1digit); • Can communicate with computer through RS-232 interface.
-
Product
Digital Panel Meters And Modules
-
Measuring Method TRMS using Microcontroller1A / 5A Input in same Meter (User Selectable)High Accuracy Accros the Entire Range9999 Count High Resolution DisplayDual Aux. 110 V AC and 230 V AC in same MeterUser Programmable Display / CTR / PTRAuto Selection of Decimal PointAuto Indication of KV & KASetup / Programmable Protected by Password
-
Product
PXIe-6535, 32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module
780695-01
-
32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module—The PXIe‑6535 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
Digital Clamp Meter
DL369
-
UEi Test & Measurement Instruments
The PHOENIX Clamp meter series starts with the DL369, the perfect meter for contractors who need basic features without all the extras. Great for general troubleshooting and electrical maintenance, this isn't just a stripped down model, the PRIME is a fully functional tough meter made to get the job done.
-
Product
Digital Mission Engineering
-
From chip to mission, connect modeling and simulation efforts across all phases of the engineering product life cycle. Model multi-domain operational environments, including land, sea, air and space, with accurate, dynamic, physics-based simulations. Integrate with the Ansys portfolio of multi-physics tools and solvers to achieve unmatched end-to-end modeling and simulation.
-
Product
Handheld Digital Multimeter, 4.5 Digit, Water and Dust Resistant
U1272A
-
Feature sets that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.6% for ACV accuracy)Intelligent features to improve productivity and safety (LPF, ZLOW, Smart )Better grip Both visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 10,000) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
Product
Digital Impact Test Machine
-
The Digital Impact Testing Machine mainly used to determine the anti-impact capability and strengthen impact toughness of non metallic materials such as nylon, glass fiber reinforced plastic, ceramic & cast stone, electrical insulating materials etc.Sample and support are easy centeringThe pendulum of the machine can be raised or released automatically by button pressedDigital LCD screen control and value displayThe machine comply with GB / T1843, ISO 180, GB / T21189, GB / T2611 and other international standard
-
Product
True RMS Digital Multimeter
MM94
-
The MM94 is a high performance True RMS multimeter with a 600V CAT IV safety rating.
It has an extended current measurement range up to 20A for short cycle measurements. Measurement capabilities include AC/DC voltage, capacitance, resistance and temperature with the included K Type thermocouple. Features include Min/Max and Peak measurement and a high frequency filter to optimise readings for distorted waveforms plus a relative mode.
The rugged design includes a 60,000 count backlit display with analogue bargraph.
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-03
-
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
-
Product
PXI Digital I/O Module With Power Distribution - Without DC-DC Converter
40-228-002
-
The 40-228 provides 32 channels of digital input and 32 channels of digital output, together with switched +12V, +5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5V supply ouput. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter (40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
Product
Digital Earth Resistance Tester, ERT-1502
-
Our Earth Tester is a very successful replacement of the conventional generator type hand tester. This device is most extensively used to test the earthing installation in numerous power based industries, electrical traction systems and telecommunication networks.
-
Product
16-Ch Universal Digital I/O Module
ADAM-5050
-
Digital input: Support Dry/Wet ContactDigital output: Open Collector to 30 V, 450 mW max. loadI/O Type: bit-wise selectable by DIP switchPower consumption: 0.35 W (typical); 1.2 W (max)Channels: 16
